Search results

Subtank nano still available? Sent from my KFTHWI using Tapatalk

Done Sent from my KFTHWI using Tapatalk

28g, 8-9 wraps around a 2mm diameter should give you around 1.6 ohm. Rebuild a few kanger coils before like this. Even the newer ones. Sent from my KFTHWI using Tapatalk

Running Linux, Fedora 21 and CentOS 7

Out of interest, have any of you tried Vape Elixir's Pure Tobacco? For a long time it was only available from eciggies but I see that Vape King now stocks them as well. I'm asking because it's been my absolute favorite and ADV for a about 3 to 4 months now.

That's interesting, I have to admit that I really don't like the TSCs on the Nautilus, but it didn't use more juice. I found that on rba my juice usage was actually less compared to a kanthal build at same wattage. At what degrees are you running cause I'm running at around the 420F (215C).

@Bill , if your able to get some boards let me know please cause I would be interested in getting one too.

None for me either.

Ok so back to the initial problem, "check atomizer". So it would seem that it's definitely the center pin not making contact with the RBA. Fixing it was fortunately, well for me at least, quite easy. Don't over tighten the RBA's center pin. So none of that "Frikkie gaan haal vir my die vise...

Since I can't find the avatar I'm looking for I'll settle for this one for now cause it's pretty spot on lately with the subtank mini.

Ha, yeah still looking for a avatar pic, basically looking for Tux vaping, or for the less informed a penguin vaping.

Stop die klok. Stop the clock. I found the f̶e̶e̶k̶i̶n̶g̶ ̶p̶u̶c̶k̶i̶n̶g̶ peek insulator. Turns out I threw it in the dustbin :oops:.

Was thinking the same, peek insulators replacing the teflon ones, but fortunately the OCC heads are really easy to rebuild. 26 gauge kanthal 6/7 wraps, 1.04 ohms is running perfect. I do however prefer the lower juice holes on the RBA to the ones on the OCC heads.

Ha ha, just my luck. Damn I really just can't win. Popped everything in the USC. Removed and dried everything. Started building the RBA. Center pin through the round peek insulator then through the base and, no no no, its gone. The flat peek insulator that goes on top of the base, missing...

Tank almost empty. Running at 20W, which for me is ALOT, sucking the life out of it. :smoke: aaaaand. Dry hit, she's empty.

Yes checked already and the insulators are in place. Figured that IF that was the case I could rather get a "short" or "low resistance" error instead.

Checked the center pin on the RBA and at first it looks like it's shorter however the RBA is screws in deeper so if you compare it at the rubber seal its the same length as the OCC Coil. Both the rDNA and the SVD 2 has spring loaded center pins however the SVD's pin is harder to push down than...

I have to agreed will all that this is an amazing little tank. And right now its all I'm using. I do however have a bit of an issue and really hope that you guys can help me or at least point me in a direction. So whenever I use the RBA I get a check atomizer on my rDNA40, well mostly. Pop...

None whatsoever. I bought a Vapor Shark rdna 40 simply because I was looking for a small box mod that can take an 18650, has proper step down with a DNA board. Sure we can probably argue on the size but it's certainly a lot smaller than a SVD 2. Been using a Nautilus, both normal and mini...

Got my subtank mini and some ni200 on Friday together with some aspire temp sensing coils. Been playing with the aspire tsc. It vapes . I'm not a high wattage sub ohmer so it's pretty much the same. Will play with the subtank mini an ni200 during the week. Been fooling around with it using...