Bought a clone of this from ft, so lets go guys.
Arrived in a box that was smaller than imagined, in fact, the actual dripper is somehow smaller than I imagined
The concept behind this is that you have a small chamber below the deck which acts as a juice reservoir, and when you feel your dripper flavour peter out, you push down and the reservoir refills your dripper
In operation, it works like a toilet cistern, but in reverse.
Theres loads of youtubes showing how it works (the original) so herewith my take on the clone that I received
Price: excellent
Machining: again, excellent
Orings/leaks: orings were tight to begin with, but some eliquid lube sorted that out. The push down mechanism has operated faultlessly thus far.
Build: I built a dual microcoil/cotton combo coming in at 0.8ohms, there are three posts but they arent drilled (same as original), you trap your kanthal under the post washers.
Airholes: wtf were they thinking: original and clone are the same...the airholes are adjustable...you get a choice of a few, but unfortunately the dual mode has the smallest pairing. This requires a drilling at some point, but for now it is "ok", but not a cloud monster. The potential is there
How do I use it: when driving, when I dont want to faff too much. I top full through the drip tip around 40 drops, then slowly push it down (to expel air) and when you again slowly release it, it will suck up the excess juice into the lower chamber. Do this one or twice slowly and you are set to go for a few hours "dripping"
Points of note: its a hybrid connection for the nemesis mod, the 1:1 20.4mm topcap version. Fasttech have recently listed the 510 adapters, but if you have a dome atty you can use the 510 adapter from that to create a 510 connection. For now, it lives on a nemesis happily. Check your nemesis, especially clones, for the outer diameter of the topcap threads before buying this...they should measure about 20.4mm...if you get closer to 20.8mm then this is not the device for you
Would I buy it again: original: no, at that price there are alternatives drippers.
clone: yes, its inexpensive, does what it says on the tin and is unique in what it does and how it does it
Summary: this device is mroe about convenience that caliornian vape scene clouds, but can hold its head amongst most middle range drippers. With larger airholes it'll be a cloud chaser, but because there is so much going on inside space wise, it'll always be at a disadvantage. No though-holes in the posts makes building low ohms coils with coathanger sized wire very difficult
Arrived in a box that was smaller than imagined, in fact, the actual dripper is somehow smaller than I imagined
The concept behind this is that you have a small chamber below the deck which acts as a juice reservoir, and when you feel your dripper flavour peter out, you push down and the reservoir refills your dripper
In operation, it works like a toilet cistern, but in reverse.
Theres loads of youtubes showing how it works (the original) so herewith my take on the clone that I received
Price: excellent
Machining: again, excellent
Orings/leaks: orings were tight to begin with, but some eliquid lube sorted that out. The push down mechanism has operated faultlessly thus far.
Build: I built a dual microcoil/cotton combo coming in at 0.8ohms, there are three posts but they arent drilled (same as original), you trap your kanthal under the post washers.
Airholes: wtf were they thinking: original and clone are the same...the airholes are adjustable...you get a choice of a few, but unfortunately the dual mode has the smallest pairing. This requires a drilling at some point, but for now it is "ok", but not a cloud monster. The potential is there
How do I use it: when driving, when I dont want to faff too much. I top full through the drip tip around 40 drops, then slowly push it down (to expel air) and when you again slowly release it, it will suck up the excess juice into the lower chamber. Do this one or twice slowly and you are set to go for a few hours "dripping"
Points of note: its a hybrid connection for the nemesis mod, the 1:1 20.4mm topcap version. Fasttech have recently listed the 510 adapters, but if you have a dome atty you can use the 510 adapter from that to create a 510 connection. For now, it lives on a nemesis happily. Check your nemesis, especially clones, for the outer diameter of the topcap threads before buying this...they should measure about 20.4mm...if you get closer to 20.8mm then this is not the device for you
Would I buy it again: original: no, at that price there are alternatives drippers.
clone: yes, its inexpensive, does what it says on the tin and is unique in what it does and how it does it
Summary: this device is mroe about convenience that caliornian vape scene clouds, but can hold its head amongst most middle range drippers. With larger airholes it'll be a cloud chaser, but because there is so much going on inside space wise, it'll always be at a disadvantage. No though-holes in the posts makes building low ohms coils with coathanger sized wire very difficult
