Baby beast rba

D

douglaswhite180

New Vaper
LV
3
 
Joined
8/8/16
Posts
26
Awards
4
Age
26
Location
ZA
So I just got a rba coil for my big baby beast (stock coils are just so expensive....) so I am using the preinstalled 0.3ohm clapton coil that comes with the rba section and there is just no flavour at all, clouds are insane but they are tasteless clouds of vapour. I first though I was wicking it wrong but no matter how I wick it there is just no flavour, it wicks beautifully and I can chain vape away.
Any advice?

Sent from my SM-G920F using Tapatalk
 
Hi buddy do you make spaced or tight coils? I found on mine that the spaced coils gives me better flavor. Maby its just all in my head dont know. but since i started slightly spacing the turns on the coil this little rebuild just works better for me..thats my 2 cents..there might be someone with much more experience and insight than me. I am a flavor chaser myself and will also follow this tread to learn some new tricks
 
Are your ohms stable? If you need to, screw and unscrew the tank a few times and check.. You are getting clouds so it is working but I'm just curious because the pre-installed coils are very big and can very easily touch the cap and also the pin 510 pins needs to be pushed right in.. My pre-installed coils on 2 rba's were impossible to use as they were too large..
 
M5000 now you mention it. I had the same problem with the pre installed coils. I had to take them out and replace with others
 
M5000 said:
Are your ohms stable? If you need to, screw and unscrew the tank a few times and check.. You are getting clouds so it is working but I'm just curious because the pre-installed coils are very big and can very easily touch the cap and also the pin 510 pins needs to be pushed right in.. My pre-installed coils on 2 rba's were impossible to use as they were too large..
Click to expand...
Unfortunately I can't check the ohms I'm running the rba off the stick v8.
And yes you are right these coils are huge and touch the top cap at times.

Sent from my SM-G920F using Tapatalk
 
PAM said:
Hi buddy do you make spaced or tight coils? I found on mine that the spaced coils gives me better flavor. Maby its just all in my head dont know. but since i started slightly spacing the turns on the coil this little rebuild just works better for me..thats my 2 cents..there might be someone with much more experience and insight than me. I am a flavor chaser myself and will also follow this tread to learn some new tricks
Click to expand...
The preinstalled coils are spaced. Definitely want to get other build for this rba though, unfortunately I cannot read ohms on the stick v8 so I will have to buy pre-made coils. Any suggestions?

Sent from my SM-G920F using Tapatalk
 
douglaswhite180 said:
The preinstalled coils are spaced. Definitely want to get other build for this rba though, unfortunately I cannot read ohms on the stick v8 so I will have to buy pre-made coils. Any suggestions?

Sent from my SM-G920F using Tapatalk
Click to expand...
i just know somebody is going to crucify me for what i am saying now...If you use nichrome 80 wire at 26GA and make 6 wraps around a 2.5mm shaft it should give you 0.32 ohm on your mod. This is wat i am vaping on sitting typing this. Please i am not saying build coils without the propper ohm meters ect..ect... that setup works for me. So if you are going to buy some coils as a present for me i would like nichrome 80 26GA 6/ 2.5mm 6 wrap please..LOL...It depends on what ohm coils you prefere...thats your personal preference... But i would say because of the small deck look at something not more than 7 wraps...preferebly 2.5mm and then when you mount them space them as close to the air inlets as possible to avoid contact with the cap you screw on..............Hey wenna now try this first.....just push those pre installed coils down closer to the air inlets. It might be that they are too high and they touch the screw on cap....Maby that just solves the problem?...Please post here if it did...only thinking about that now...hopes this helps....and the gurus......please downt burn me at the stake....again i say its not wise to build coils without the propper goodies asosiated..
 
PAM said:
i just know somebody is going to crucify me for what i am saying now...If you use nichrome 80 wire at 26GA and make 6 wraps around a 2.5mm shaft it should give you 0.32 ohm on your mod. This is wat i am vaping on sitting typing this. Please i am not saying build coils without the propper ohm meters ect..ect... that setup works for me. So if you are going to buy some coils as a present for me i would like nichrome 80 26GA 6/ 2.5mm 6 wrap please..LOL...It depends on what ohm coils you prefere...thats your personal preference... But i would say because of the small deck look at something not more than 7 wraps...preferebly 2.5mm and then when you mount them space them as close to the air inlets as possible to avoid contact with the cap you screw on..............Hey wenna now try this first.....just push those pre installed coils down closer to the air inlets. It might be that they are too high and they touch the screw on cap....Maby that just solves the problem?...Please post here if it did...only thinking about that now...hopes this helps....and the gurus......please downt burn me at the stake....again i say its not wise to build coils without the propper goodies asosiated..
Click to expand...
i really need to go to bed now........rerig.... i just reposted everything that was said by using other words....sorry
 
4 Wraps on 3mm ID spaced coil works like a charm for me at 35 watts and .287 ohms
 
douglaswhite180 said:
The preinstalled coils are spaced. Definitely want to get other build for this rba though, unfortunately I cannot read ohms on the stick v8 so I will have to buy pre-made coils. Any suggestions?
Click to expand...

Building with premade coils or your own coils would require an ohm meter of some sort.. You need the ohm meter to make sure that the coils are installed correctly and are giving the correct reading.. The TFV8 is known to have a 510 pin that needs some tinkering at times and without an ohm reading you won't know when this is the case.. This tank just happens to be a bit of an ohm jumper! A protected mod is useful and an experienced user installing a straight wire coil on the rare occasion might not be too risky, but seriously don't get into rebuilding without something to read ohms.. I had protection fail on a Therion so trust me if a DNA can fail so can the SMOK..

I think those coils may not work, touching the top cap is BAD. Reducing the size may bring the ohms too low I don't know your battery specs but you can try squeezing and lowering it but make sure the coils don't touch any metal whatsoever and they must fire simultaneously from the centre outwards.. That rba has weak screws so be gentle and don't over-tighten.. I had a loose 510 pin out of the box which caused jumping ohms so just check that the pin underneath is sitting firmly..

@PAM the admin are getting your coils ready :thumbup:
 
PAM said:
i just know somebody is going to crucify me for what i am saying now...If you use nichrome 80 wire at 26GA and make 6 wraps around a 2.5mm shaft it should give you 0.32 ohm on your mod. This is wat i am vaping on sitting typing this. Please i am not saying build coils without the propper ohm meters ect..ect... that setup works for me. So if you are going to buy some coils as a present for me i would like nichrome 80 26GA 6/ 2.5mm 6 wrap please..LOL...It depends on what ohm coils you prefere...thats your personal preference... But i would say because of the small deck look at something not more than 7 wraps...preferebly 2.5mm and then when you mount them space them as close to the air inlets as possible to avoid contact with the cap you screw on..............Hey wenna now try this first.....just push those pre installed coils down closer to the air inlets. It might be that they are too high and they touch the screw on cap....Maby that just solves the problem?...Please post here if it did...only thinking about that now...hopes this helps....and the gurus......please downt burn me at the stake....again i say its not wise to build coils without the propper goodies asosiated..
Click to expand...
Thanks for the advice it really helped, pushing the coils lower also helped with the flavour a lot. Still not the most intense flavour but it's there. Not the hot flavourful burst of vape I'm looking for though. I am really looking into getting a decent mod but cannot at the moment so I will just check ohms and that on a friends mod for now.

Sent from my SM-G920F using Tapatalk
 
Arthur said:
I could maybe help you out. I am also in kempton and build my own coils for the V8 and Baby beast. I have no problems with flavour or clouds.
Click to expand...
Oh awesome. Round about which area of kempton?

Sent from my SM-G920F using Tapatalk
 
You must log in or register to reply here.

Similar threads

WintersFrost
Surprise !! I'm Back Baby
Replies
8
Views
395
WintersFrost
WintersFrost
Zeki Hilmi
Cthulhu Diver RBA Mod
Replies
3
Views
543
SteamServant
SteamServant
L
  • Question
SMOK TFV8 BABY V2 - Leaking
Replies
2
Views
229
Lt-Flealick
L
blujeenz
Any embedded engineers/hobbyists here?
Replies
10
Views
193
blujeenz
blujeenz
Old_Goat
RipSaw RDA by Bearded Viking Customs and Suicide Mods
Replies
0
Views
452
Old_Goat
Old_Goat
Back
Top