Dem builds
- Thread starter wiesbang
- Start date
I haven't installed it yet it has been a busy week and weekend hoping to install it tonight and some fresh coils dor my goon as well.
I am hoping that the ohms will be approximately the same as 3 x28ga but with the added benefit of a quicker rampup but will give feedback as soon as I have installed it.
Built and ready to go 0.42 ohms 5 x 32ga aliened with 38ga ni80 2.5mm
So my thoughts on this the flavour is good but not getting that quick rampup I was hoping for I think this build might shine in a deul coil setup on a mec but not that great in single on a mec but I have been liking hotter vapes lately. Think it's going to be great with battery life. At least the flavour is good. Compared to a 3 x 28ga alien the ohms are a little bit higher and the rampup might be faster if I remove a wrap and get it a little bit lower.
So my thoughts on this the flavour is good but not getting that quick rampup I was hoping for I think this build might shine in a deul coil setup on a mec but not that great in single on a mec but I have been liking hotter vapes lately. Think it's going to be great with battery life. At least the flavour is good. Compared to a 3 x 28ga alien the ohms are a little bit higher and the rampup might be faster if I remove a wrap and get it a little bit lower.
3 x 32ga ni80 aliend with 38ga ni80 2.5mm 0.6ohms not my best but will serve it's purpose. 
Last edited:
4 x 0.3mm ni80 bordered with 28ga ni80 aliend with 38ga ni80 0.11 ohms
Last edited:
Jip I do all of it free hand.
- Joined
- 16/6/16
- Posts
- 3,515
- Awards
- 37
- Age
- 54
Lost my fralien i made for the Tauren One RTA i want to review tomorrow so had to make a new one.
Not bad for a old man.
2x28ga SS bordering 4x(0.3x0.1mm) Nichr80 ribbons claptoned by 36ga Nichr80.
Not bad for a old man.
2x28ga SS bordering 4x(0.3x0.1mm) Nichr80 ribbons claptoned by 36ga Nichr80.
Anyone know what you call this wire/coil? Got it in a packet with a atty but only say ni80. Nice crisp taste on the fruits
- Joined
- 16/6/16
- Posts
- 3,515
- Awards
- 37
- Age
- 54
Looks like a braided coil from Geekvape.
https://www.geekvape.com/project/2-in-1-coils/
https://www.geekvape.com/project/2-in-1-coils/
Hey man. I see you set your coils quite far to the sides on the goon. Does this have a particular purpose? Flavor? Clouds?
For me it does serve a purpose I use my goon with two holes open so I try and align my coils with those two holes hitting them center and only the bottom of the coils just visible trough those holes it gives better flavor for me.
Lost my fralien i made for the Tauren One RTA i want to review tomorrow so had to make a new one.
Not bad for a old man.
2x28ga SS bordering 4x(0.3x0.1mm) Nichr80 ribbons claptoned by 36ga Nichr80.
View attachment 174242 View attachment 174243 View attachment 174244 View attachment 174245
These look awesome.
Glad to see some builds from you again.
Attempt at a helix build.
8 x 0.3mm ni80 bordered with 32ga x2 wrapped with 40ga
8 x 0.3mm ni80 bordered with 32ga x2 wrapped with 40ga
3 x28ga ss317ga aliend with 38ga ni80 2.5mm 0.32 ohms
Holy moly that build is clean. Nice job @Friep
Coil for the skyfall came out great!
This looks like a stunning coil to try in replay mode!
Similar threads
