Dem builds

d35172075623b62bef539c7580d6d4f5.jpg


It is my first time building and I just want opinions on how it looks please and any suggestions, thanks.


Sent from my iPhone using Tapatalk
 
d35172075623b62bef539c7580d6d4f5.jpg


It is my first time building and I just want opinions on how it looks please and any suggestions, thanks.


Sent from my iPhone using Tapatalk

Hi @efdsantos99
Have moved this post of yours to a general build thread
You posted it inside one of the dedicated vendor subforums and they requested it be moved to a more appropriate general thread. I see you posted this in that Ammit thread as well.
 
hi @efdsantos99

That build looks fine, sir! Excellent for a first attempt!
To improve it, you should use a finer gauge wrap wire, and try and get your stagger-spacing tighter, so that you have less gaps.

: )
 
d35172075623b62bef539c7580d6d4f5.jpg


It is my first time building and I just want opinions on how it looks please and any suggestions, thanks.


Sent from my iPhone using Tapatalk

I'm no pro when it comes to the dual coil ammit, but if it anything like the single coil, you have too much cotton there. The possibility of dry hits is real.
Try trimming the cotton so it doesn't come out of those holes at the sides, but just sits there ready to suck up some juice.
Other than that, it looks clean. Job well done!


Sent from my iPhone using Tapatalk
 
Playing around with a build for my Entheon on the MaTo squonker. I decided to go with a pentacore alien, 5 x 28ga fused with 36ga alien, all ni80, 3mm id. I removed a wrap from the original coil to bring the resistance down. A healthy 0.14ohm post fire IMG_20171107_183822.jpg IMG_20171107_192448.jpg IMG_20171108_011430.jpg IMG_20171108_011545.jpg
 
20171107_071246.jpg
Playing around with a build for my Entheon on the MaTo squonker. I decided to go with a pentacore alien, 5 x 28ga fused with 36ga alien, all ni80, 3mm id. I removed a wrap from the original coil to bring the resistance down. A healthy 0.14ohm post fire View attachment 112647 View attachment 112648 View attachment 112649 View attachment 112650
Please let me know how she vapes? I recently acquired a Entheon and for my first build, I chucked a big old framed staple in there. Must admit, I am a bit underwhelmed. I think the build might be too big for the atty as she has a lack of airflow and gets hot pretty quick! I don't want to just write her of as I heard good things about it, but so far it's been pretty meh!
Btw. I am open to any help/suggestions!
 
Last edited:
Please let me know how she vapes? I recently acquired a Entheon and for my first build, I chucked a big old framed staple in there. Must admit, I am a bit underwhelmed. I think the build might be too big for the atty as she has a lack of airflow and gets hot pretty quick! I don't want to just write her of as I heard good things about it, but so far it's been pretty meh!
Btw. I am open to any help/suggestions!
The Entheon is definitely not one for big airy builds.

Personally I build for around 0.5-0.6Ω and vape at 20-25W.
I do prefer the more restricted draw on the Entheon though.
 
The Entheon is definitely not one for big airy builds.

Personally I build for around 0.5-0.6Ω and vape at 20-25W.
I do prefer the more restricted draw on the Entheon though.
I am all for a restricted draw but I think my build might be choking it. I also think getting a bigger drip tip might improve the situation as I find it very difficult to get my mouth around that short/small diameter drip tip!
 
I have been using so Mohawk aliens in my goon for a while now and just love the smoothness of the vape I get of them! definitely considering a single Mohawk 3mm 5wrap to mellow things out!
 
I am all for a restricted draw but I think my build might be choking it. I also think getting a bigger drip tip might improve the situation as I find it very difficult to get my mouth around that short/small diameter drip tip!
Oh I definitely agree about the drip tip... I'm much happier with this:
1Eovf1X.jpg
 
Oh I definitely agree about the drip tip... I'm much happier with this:
1Eovf1X.jpg
now that sommer looks inviting to the lips!lol I must say I love the look of the Entheon with the standard drip tip...so classy but a little bit unpractical!
 
View attachment 112662
Please let me know how she vapes? I recently acquired a Entheon and for my first build, I chucked a big old framed staple in there. Must admit, I am a bit underwhelmed. I think the build might be too big for the atty as she has a lack of airflow and gets hot pretty quick! I don't want to just write her of as I heard good things about it, but so far it's been pretty meh!
Btw. I am open to any help/suggestions!
She's vaping a treat brother, the airflow issue can only be rectified by a smaller id, try going with a 2.5mm id and let me know how she vapes
 
now that sommer looks inviting to the lips!lol I must say I love the look of the Entheon with the standard drip tip...so classy but a little bit unpractical!
A much better experience. I can definitely recommend you give it a try.
Yeah the stock tip looks fantastic ... but it ends at "looks" :p
 
The Entheon is definitely not one for big airy builds.

Personally I build for around 0.5-0.6Ω and vape at 20-25W.
I do prefer the more restricted draw on the Entheon though.
I also prefer higher builds but this is going on a mech squonker so between 0.1-0.15 works perfectly
 
I have been using so Mohawk aliens in my goon for a while now and just love the smoothness of the vape I get of them! definitely considering a single Mohawk 3mm 5wrap to mellow things out!
Mohawk aliens are great but with the way the airflow hits the coil in the entheon you're gonna get spit back so stick to a normal alien. If you're using a regulated device try a 3 x 26ga fused with 36ga alien, 5 wraps, 3mm id should read at about 0.2, on a mech try the 5 x 28ga fused with 36 or 38ga
 
My OCD got the better of me with the clamps moving inward due to them being flipped so I rebuilt for aesthetic purposes with the coil legs below the coil so tightening the screws push the clamps flush to the post guide rather than inwards. I also took a pic from the side for @Dexter305 to note the height of the coil. It's now reading at 0.15 due to the longer coil legsIMG_20171108_112817.jpg IMG_20171108_113531.jpg IMG_20171108_113611.jpg IMG_20171108_113450.jpg
 
Mohawk aliens are great but with the way the airflow hits the coil in the entheon you're gonna get spit back so stick to a normal alien. If you're using a regulated device try a 3 x 26ga fused with 36ga alien, 5 wraps, 3mm id should read at about 0.2, on a mech try the 5 x 28ga fused with 36 or 38ga
Thanks for all the advice buddy, normal alien it is then...I primarily use NI80, think I will try 28x3 fused with 36 but I am going to follow your advice and try a 2.5mm ID 6 wraps?
 
Thanks for all the advice buddy, normal alien it is then...I primarily use NI80, think I will try 28x3 fused with 36 but I am going to follow your advice and try a 2.5mm ID 6 wraps?
The amount of wraps depend on the surface area of the coil, just do enough wraps to fit post to post or it'll be a pain to install
 
Oh man, those broad 5core aliens look so nice!!! Thanks for all the advice @Moey_Ismail I will be sure to let you know how it turns out!

btw. how difficult is it to trim the leads off the coil after you've tightened it on the Entheon! The clippers just cant get in there! That get my OCD going sometimes!:eyepop:
 
Oh man, those broad 5core aliens look so nice!!! Thanks for all the advice @Moey_Ismail I will be sure to let you know how it turns out!

btw. how difficult is it to trim the leads off the coil after you've tightened it on the Entheon! The clippers just cant get in there! That get my OCD going sometimes!:eyepop:
Thanks bud, just bend them upwards at a 90 and snip, if it's still in the way use a flat screwdriver to press them against the clamp
 
Back
Top