Is it better to leave it that short next to the coil? What's the advantages compared to leaving it longer?
Dry Hits Every 3 Hits
- Thread starter bjorncoetsee
- Start date
I have also found that it works better if it is that short, I think it feeds easier than a whole bunch of cotton.
Just did one where it just touches the post. Will try it and see how it goes.
I guess that's the right way then @capetocuba?
All I can say is since I started using thinner and shorter wicks my RM2 experience got way better!
@bjorncoetsee any luck on your side?
Just check that your juice cap seal is still seated in place properly. I find that if I over tighten the bottle cap it distorts the seal which either causes juice to leak out inside when sqonking or displace more air than juice so the wick never gets a proper dunking.
Easy solution, drill out the airhole to 2 or 3 mm, use 28 gauge and do a parallel wrap, 7 or 8 turns should do the trick. When wicking, use Rayon and loop the little tail ends just under the coil. When screwing on the reomizer top, make sure your airholes line up with the coil.
What I do, is when I squank, I make sure I can see liquid in that 3mm air hole, once I see that, I release the squank and vape like a steam train. I find I can then take +- 5 hits before any remote taste of dryness occurs. You will however get used to the frequency of sqonking eventually.
Many might say 3mm is too wide for the air hole, I love the airy draw and loads of clouds. Bowdens Mate gives a good kick with that setup. I am still experimenting with Paris(My Reo) but will tune if I find any other wicked ideas. Hope this can be of some help.
3mm is way to big for a rm2 unless he is in to lung hits. I wouldnt drill a rm2 to 3mm. will bring the hole lower down to the deck and more then likely will leak through the airhole.
Sent from my GT-I9500 using Tapatalk HD
And I thought my 1.5mm hole was big!
Eish I have to disagree there sir drilling that RM2 anything bigger that 1.5mm and you start losing flavour considerably. That 8 wrap parralel is also very long and it gets a bit to hot for rayon and burns it. Anyway this is my finding anyway.
To get use to squonking @Andre provided this tip. Remove driptip, look into the rm2 and squonk you can watch whats happening.
you are safe my friend. BTW nice coilsAnd I thought my 1.5mm hole was big!
Sent from my GT-I9500 using Tapatalk HD
Also, if your wick is packed too tight in the coil, it won't saturate enough and you can get nasty dry hits from that. Your wick should fit loosely in the coil. Had some nasty dry hits in my life and learned the hard way...lol
Shorter wicking is definitely better on the Reomizer. Very long thread on ECF has proven this beyond doubt. Do not wick it like a dripper.
Seem to get the same amount of hits with the shorter wick.
The OP said he used Rayon. Most recommend more Rayon than with cotton - thickness, not length. Did not know you had experience with the reomizer?
Coil is a coil is a coil is a coil.
I didnt know you used magically special unique wire for your reomizers that would fit no other product...
We are talking about a wick here, which is what you commented on. And on a reomizer wicking is another kettle of fish.
Noted for future.
Dont get me wrong but I dont think you know what you talking about.Coil is a coil is a coil is a coil.
I didnt know you used magically special unique wire for your reomizers that would fit no other product...
Sent from my GT-I9500 using Tapatalk HD
no need to apologise brother.
Sent from my GT-I9500 using Tapatalk HD
Sent from my GT-I9500 using Tapatalk HD
Similar threads
