Together with the Aegis X kit, GeekVape sent me their newest Aegis Squonk Box Kit, integrating an Aegis Squonker Mod and a Bottom Feed Tengu RDA. This kit is equipped with the advanced AS-100 Chipset and features rapid and responsive firing times, allowing the use of atomizers with a resistance as low as 0.05ohm and identifying any attached atomizers accurately.
Item Name : Geekvape Aegis Squonk
Manufacturer: @geekvape
Website: https: www.geekvape.com
Cost: $92 (Converted R1390)
***DISCLAIMER*** This device was supplied to me by @geekvape for the purpose of reviewing the product for them and providing my personal feedback and opinion of this device. I’m not being paid for this review and this review is my own opinion and views.
Let me start by shows you some unboxing pictures:
The box below is the review sample box and the retail version will have all the fancy pictures ect.
What’s inside the box you ask?
1x Aegis Squonk Mod
1x Battery Door Assist Tool
1x L-Shaped Hexagonal Wrench
2x N80 Fused Clapton Coil
1x GV Triangular Tool
1x 510 Drip Tip Adaptor
1x Squonk Bottle
1x Tengu RDA
1x 810 Drip Tip
2x Feather Cotton
Note: The extra conversion plate to change the mod from a squonk to a normal single battery vape is not included in standard packaging and will be available to buy as an extra. This was only included in the reviewers samples.
Technical specifications are also important, so here they are:
Aegis Squonk Mod
Size: 86.5x 41.2x 31.5 mm
Thread connection: 510
Chipset: AS-100 Chipset
Wattage output: 5- 100W
Screen: OLED Display Screen
Resistance range: 0.05- 3.0ohm
Modes: Power/ VPC/ TC/ TCR/ Bypass
Temperature Range: 100- 315℃/ 200- 600℉
Battery type: Single 18650 (Not included)
Material: Plastic & silicone & SS & Zinc alloy
Protection: 10s Cut-Off/ Short-Circuit/ Over-Charging & Discharging/Over-Heat/ Over-Current/ Anti-Dry Protection
Tengu RDA
Size: 24x 28.3mm
Juice well: 6mm deep
Thread connection: 510
Drip Tip: 810 Widebore
Material: SUS303 & Acrylic
Configuration: Single/ dual coils
Overview
So, what do I think about this device?
Real simple, this is an Aegis Solo, uses the same AS100 chip set and functions exactly the same as one but now has a built in squonk bottle with some innovative design to get the bottle to squonk up the the RDA which i think is really cleaver. The 510 housing does not squonk through the 510 connection but rather around the pin and uses grooves in the 510 pin on the RDA to feed the liquid up and push it out of the middle post.
Looks?
Mmm okay so put in simple terms, as mentioned Its basically a Aegis Solo that has a squonk bottle built into it. Its features a very simalar design, shape but due to the built in bottle, the device is a little longer to make space for the bottle at the back. The Tengu RDA looks great as well and has been out for a couple of months and nothing of this RDA stands out as new but its a design that works great, simple looks and easy to use.
Squonking - How it works:
The Aegis squonk has been designed to be one unit and works great as the squonk bottle is connected to a plastic tube that feeds to the 510 connection. The Squonk pin on the RDA and the 510 pin has grooves in them. When squonking, the whole 510 housing on the inside fills with liquid and then pushes up though the groves up into the middle post of the RDA which has two tiny holes where the liquid will then fill the well.
After you are finished, the excess juice will then get sucked back into the bottle.
RDA, Squonk & Flavor:
The Tengu RDA is great, simple but great. The middle post is gold plated and also connects to the 510 pin. The deck has two very small holes on the bottom on each side where the eliquid comes out and fills the juice well. The RDA has air holes that perfectly line up with the coils and provides excellent airflow straight onto the coils giving you great flavor!
Its a super easy RDA to build and there is nothing to it. I built the RDA with the two N80 Fused clapton coils that comes supplied with the kit and also used the cotton and so far its pretty awesome flavor!
The top cap has two pins which slot into the base of the RDA that ensure the inside of the top cap is fixed to one place leaving the outer side of the top cap free to move allowing the air holes to adjust.
Here i have installed the two coils that come with the kit and i must say they provide excellent flavor, no spitback and were easy to setup. There wasnt much hot spots and they both heat up nice and evenly.
Changing from Squonk to Mod:
Changing from the Squonk to the mod is easy as chips! Undo the two top allenkey screw and the squonk part simply pulls away from the mod. Attach the non squonk cover and tighten the screws again.
Cleaning:
Cleaning the Squonk bottle requires a little more work:
Step 1 : Remove the squonk cover from the mod
Step 2 : Slide open the fill cover and remove two small silicone plugs
Step 3 : Remove the two screws under the silicon plugs
Step 4 : Squonk bottle is now loose and needs to be pulled through the housing
Reverse order to fit back to the mod.
BUT - I have seen a video from Geekvape where they put the whole mod underwater and just squonk it, this will suck liquid into the bottle and by pushing the bottle will squonk water back out cleaning the whole system including the 510 pin.
How’s the Vape?
This being my first ever squonk device, i am blown away and wish i had tried squonking alot earlier! I have always been a fan of dripping but having to drip every couple of pulls annoyed me. With one deep push on the bottle for a second or two, the juice well fills up wetting the wicks and you are ready to vape. Flavor is excellent as drippers usually do, but yeah she is a little thirsty.
The overall vaping experiencing is total bliss but using a single 18650 is a pain especially at 70W to heat the two Fused Claptons to a good level, the battery level tends to drop fairly quickly. I would have given this squonk a 10/10 rating if it was released with a 21700 battery or if it had the option of taking both a 18650 or 27100 battery, that would have been awesome!
Colors/designs available:
Several great colors will be available, I love the blue and the green ones!
My Pro's
IP67 Dust, Waterproof, Shock resistant
Build quality is really good
Built in squonk bottle with replacement/spare bottle in parts
AS 100 chip provides fast response firing
No leaking from the squonk bottle, RDA ect
Super easy to setup, even for a squonk noob like me!
Quality N80 Fused Clapton Coils, Coil tool, Cotton all included.
Plenty of spare parts are included (Retail package wont have the conversion cover - Sold separate)
Great flavor from the Tengu RDA
Smooth draw with no whistling from the RDA
Easy to use menu on the mod and switch between modes
My Cons's
Allen key provided to remove the cover slips, had to get a better one from my tools to remove the allen key in order to change covers.
Single 18650 battery mod, probably the biggest con...could have been a 21700 mod for better battery life
Replacing/cleaning the squonk bottle is a pain in the bum! its a mission getting the bottle in and out of the cover but its due to IP67.
My Verdict?
Let keep it simple, If you liked the Aegis Solo but love squonking, This is for you! Paired with the Tengu RDA in the kit and also being able to buy the separate cover to change it to a normal Solo will leave you with one mode but two options. Some might probably say its stupid and why not just by a Solo...i get it but we all know how people are and that we are sometimes a little undecided lol So here if you get sick of squonking, you can buy the extra cover. Its an awesome kit, looks great and is IP67 so it will almost be indestructible!
Would I buy one or recommend one?
I might be converted from RTA to Squonking....so Bloody hell i give it a 9 out of 10 yesses!!