Guys need help

[Darryn Du Plessis]

Sorry guys but i dont think prob is the build if i use my std build 26g 5/6 wrap i usually get 0.5 ohm if not 0.4 ohm every single time for the past couple of months.

Now since today i get a short on the battery and its a constant short error displayed on screen

Extend the gap between the hole and the atomizer . Stick your rod through the coil and raise it up. Tighten those screws again. Should help you out. AND make sure that the sides past the screws are clipped with a nailclipper. That's what's touching the sides. I had the exact problem some months ago

 

[Dubz]

There could be a metal shaving or off-cut of wire lodge somewhere in the rba causing a short. Maybe a good scrub in hot soapy water will work - strip it down first though.

 

[Darryn Du Plessis]

Have a look at those close up pics u will see that the plastic gasket is not allowing the flowting post to touch anywhere

That right hand side has a piece of the metal coil sticking out that I know it will touch the side of the spin around Deck. Also, another piece of advice would be to get the v2 deck sold seperately. it performs better with juice control upgraded as well as some more insulation for the middle chimney to attach to the deck comfortably.

 

[sabrefm1]

Update: my battery seems to be the culprit. Had it tested by vapemob. My subtank reads 0.3 ohm on my battery. On a evic vtc it reads 0,57 ohm. Fires nicely no shorts or anything. When placed back on my istick i get atomizer short error

 

[sabrefm1]

So check this. I got so fed up so tried to fix this battery. I manually shorted the battey by firing a new coil by put a pliers on top of coil and firing it. After that guess what we got power. Now the coil isnt 100% as i get spit backs so that coil needs adjusting but im scared to tinker with it incase it stops working. Maybe il try to build a new coil tomo but eventually will need to

 

[sabrefm1]

As u can see in the pic the coil has some uneven gaps

 

[sabrefm1]

so victory hasnt lasted long at all. charged my battery this morning and started vaping with a full tank. the battery slowly started to die out as if it was functioning like a mechanical mod. you know that feeling when your battery starts dying and you starting pulling in harder as you not getting enough power. on the screen the watts and voltage still the same. even if i push it all the way up to 30watt no luck. power just goes slowly down

 

[Clouder]

Dang @sabrefm1 what a bummer! But atleast now you have a REASON for some VAPE MAIL, BABY!!!!!!!!!!!!!

 

[KimVapeDashian]

Sorry to hear about your hardware issues man.

So check this. I got so fed up so tried to fix this battery. I manually shorted the battey by firing a new coil by put a pliers on top of coil and firing it. After that guess what we got power. Now the coil isnt 100% as i get spit backs so that coil needs adjusting but im scared to tinker with it incase it stops working. Maybe il try to build a new coil tomo but eventually will need to

Was there a reason to this (reddit/youtube), or just out of frustration?

so victory hasnt lasted long at all. charged my battery this morning and started vaping with a full tank. the battery slowly started to die out as if it was functioning like a mechanical mod. you know that feeling when your battery starts dying and you starting pulling in harder as you not getting enough power. on the screen the watts and voltage still the same. even if i push it all the way up to 30watt no luck. power just goes slowly down

Do you have access to a basic volt meter? If so, what readings are you getting from your mod?

 

[sabrefm1]

well u see i studied electric engineering in college so always that guy that tinkers with these stuff. but my level of electronics aint that great but decided out of frustration just to open the thing up and see whats potting and try what ever i can. i have a multimeter but its at home atm