Hadaly RDA Build ..... pity :)

KZOR

Proudly South African Vaper
LV
39
 
Joined
16/6/16
Posts
3,514
Awards
37
Age
54
Location
Bellville, Cape Town, Western Cape, South Africa
This build produces such good flavor but ..........
Tried something new by wrapping a clapton around a rectangular bar as to maximise the surface area of the saturated cotton as well as enhance the flavor by lowering the coils closer to the internal air outlets.
Only problem is that the coils are closer to the clamp posts and heat up the atty alot quicker.
Up side is that the flavor is definitely enhanced. :)

DSC_0122.JPG DSC_0123.JPG DSC_0111.JPG DSC_0112.JPG DSC_0114.JPG DSC_0116.JPG DSC_0120.JPG DSC_0121.JPG
 
Very cool! Perhaps with a smaller diameter flat bat the coil won't be so close to the posts?
 
2017-04-08 14.12.21.png

Interesting idea, if i Could respectfully add my 2c, try wrap the coil in the other direction, use a slightly narrower bar and when fitting the coil try lower the bar against the rda walls, . . When you look through the air flow holes the bottom of your coil should be visible

Peace
 
Sorry, I'm clueless at coils but what if you made it vertically? It would necessitate some funky bends to get the bottom coil leg up into the clamp. But if you want to go rectangular and you want to keep the coil edges away from the posts, wouldn't a taller thin rectangular coil be better than a squat, fat one? Dunno how it would affect the airflow and wicking, though.
 
Interesting. The coil to wick surface area remains unchanged irrespective the coil shape, the only change at coil level would be the smaller wick capacity therefore less juice is being contained in the wick inside the coil. From that, the juice inside the wick should run hotter as the same energy as usual is applied do a smaller volume.

Changes in result should thus have their origin in changed airflow rather than at the point of evaporation. Me thinks anyway...
 
Coil area will be the same but a rectangular builds will increase the cotton area that is closer to the coils hence more juice evaporated when fired.
In a rectangular build the coils are closer to the centre of the cotton than a circular build.
Due to the cotton in the corners of the coil being shared (Within the 90 degree bends) by the coil on two sides of it, the volume is actually reduced. As is the total volume of cotton which must both serve as heating medium and replenishment channel is also reduced, coil performance should be impeded overall. In addition, the cotton volume sharing in corners should also cause uneven heat distribution over the heating surface.
 
Any
Due to the cotton in the corners of the coil being shared (Within the 90 degree bends) by the coil on two sides of it, the volume is actually reduced. As is the total volume of cotton which must both serve as heating medium and replenishment channel is also reduced, coil performance should be impeded overall. In addition, the cotton volume sharing in corners should also cause uneven heat distribution over the heating surface.
if I may ask any suggestions on what type off wire I must start with if I have a Hadaly. The inner diameter coil positioning that I can figure out for myself but everyone have different opinions about wire just want something simple for beginning to get me going.
 
Any if I may ask any suggestions on what type off wire I must start with if I have a Hadaly. The inner diameter coil positioning that I can figure out for myself but everyone have different opinions about wire just want something simple for beginning to get me going.

Hi @Dolfie, took me a while to get to an answer on this.

Firstly, getting two vapers to agree on a best anything is like asking to understand what goes on in a woman's mind. Seldom happens and even then only for very short duration's in time. I think you answered it yourself. Start simple with what you have and extend on it from there.

Regards
 
Hi @Dolfie, took me a while to get to an answer on this.

Firstly, getting two vapers to agree on a best anything is like asking to understand what goes on in a woman's mind. Seldom happens and even then only for very short duration's in time. I think you answered it yourself. Start simple with what you have and extend on it from there.

Regards
Thanks so 24 Kanthal is that simple enough
 
Thanks so 24 Kanthal is that simple enough
Yip, Kanthal is nice and stable. Rather high in resistance but after all is said and done, its the watts that count not the resistance. Go on to experimenting with Kanthal Clapton wire and so on and so forth.

There is no easy way to learn what is right for you in any specific atty. And only you will know when you strike gold. Get yourself a couple of different wires and play around to find your sweet spot.

Regards
 
I prefer a 316L coil in both my Hadalys so I can TC the crap out of them

But in the end it's up to you to decide what works best for you.

Sent from my iPhone using Tapatalk
 
Back
Top