Hi Guys,
Doing this write up as requested...
First off, Please note, I am not for one second suggesting that this is the "right' way to wick OR fill the Mutation MT RTA, but, it is the way that I do it, and it works great.
Now....
Wicking
In this thread, I am using a single coil setup - for dual coil setups, simply repeat the process on the second coil.
1) Take tank completely apart and wash it thoroughly. I use dishwashing soap and the steps I take are as follows: a) Let sit in warm soapy water. b) shake all parts in the water and wash using a toothbrush c) rinse with clean cold water d) dry and blow out any water from all parts.
2) Dry burn your coil. (For the purpose of this writeup, I am not explaining coiling on this tank).
Excuse my ill-shaped coil, I will be receiving my coil jig in a day or two - you'll see it in the Vape Mail Thread. Then I'll do some PROPER coils. Also, I am waiting for the jig before I waste more wire on badly shaped coils, hence the single coil.
3) Put on the bottom O-ring. I do this so that I do not disturb the wicking afterwards.
4) Cut your wick about 4mm in width, twist the end and insert through coil. Cut wick to length (I keep it LONG) and heavily fluff the ends.
5) Insert the wick from the outer end into the juice well.
And again.
Now flatten it by pushing on it with the stem of a screwdriver.
Note, the threads of the Chimney must be clear of any wick.
6) Prime the wick with jooooooooose
7) Screw on Chimney cap
Filling with E-Juice
1) With the Mutation MT RTA Wick'd and primed with juice, put on glass tank with top o-ring installed
2) Install top Chimney. Make sure everything is tightly screwed in.
3) Install Airflow adjuster and keep in closed position
4) Fill with E-juice. Make sure there is enough space in the filling hole that air can escape WHILE the new juice is going in!
5) Install top cap with only half a thread. Turn tank upside down and screw in the top cap completely (while tank is upside down).
6) Turn tank right side up and open the air adjuster completely
7) Allow 10 minutes with the e-juice to saturate the wicks before vaping.
P.S. Guys I'm sorry about the pictures being sideways, Hopefully the MODS will be so kind as to fix it for me... @Silver ?
Thanks for reading!
Doing this write up as requested...
First off, Please note, I am not for one second suggesting that this is the "right' way to wick OR fill the Mutation MT RTA, but, it is the way that I do it, and it works great.
Now....
Wicking
In this thread, I am using a single coil setup - for dual coil setups, simply repeat the process on the second coil.
1) Take tank completely apart and wash it thoroughly. I use dishwashing soap and the steps I take are as follows: a) Let sit in warm soapy water. b) shake all parts in the water and wash using a toothbrush c) rinse with clean cold water d) dry and blow out any water from all parts.
2) Dry burn your coil. (For the purpose of this writeup, I am not explaining coiling on this tank).
Excuse my ill-shaped coil, I will be receiving my coil jig in a day or two - you'll see it in the Vape Mail Thread. Then I'll do some PROPER coils. Also, I am waiting for the jig before I waste more wire on badly shaped coils, hence the single coil.
3) Put on the bottom O-ring. I do this so that I do not disturb the wicking afterwards.
4) Cut your wick about 4mm in width, twist the end and insert through coil. Cut wick to length (I keep it LONG) and heavily fluff the ends.
5) Insert the wick from the outer end into the juice well.
And again.
Now flatten it by pushing on it with the stem of a screwdriver.
Note, the threads of the Chimney must be clear of any wick.
6) Prime the wick with jooooooooose
7) Screw on Chimney cap
Filling with E-Juice
1) With the Mutation MT RTA Wick'd and primed with juice, put on glass tank with top o-ring installed
2) Install top Chimney. Make sure everything is tightly screwed in.
3) Install Airflow adjuster and keep in closed position
4) Fill with E-juice. Make sure there is enough space in the filling hole that air can escape WHILE the new juice is going in!
5) Install top cap with only half a thread. Turn tank upside down and screw in the top cap completely (while tank is upside down).
6) Turn tank right side up and open the air adjuster completely
7) Allow 10 minutes with the e-juice to saturate the wicks before vaping.
P.S. Guys I'm sorry about the pictures being sideways, Hopefully the MODS will be so kind as to fix it for me... @Silver ?
Thanks for reading!
Last edited:
, covered all the requirements. I'm sure this will help anyone having an issue with the mutation rta . I build my tank the exact same way now & haven't experienced leaking/dry hits since
