Odis Flow Ti

Quickly put in a 2.5mm fused Clapton 0.36ohm and man o man is the flavor good :)
just a note put the chimney in the boro first :)
and SXK BB users you can't screw the top tingy for the driptip in all the way down :)
 
Just a quick question @Rob Fisher or any other Flow users

Does it work the same as the Exocet?
Ie taking out and putting in to the Boro
And building the coil and wicking?

Or are there any important differences that one needs to know ?
 
Just a quick question @Rob Fisher or any other Flow users

Does it work the same as the Exocet?
Ie taking out and putting in to the Boro
And building the coil and wicking?

Or are there any important differences that one needs to know ?
see above
 
Just a quick question @Rob Fisher or any other Flow users

Does it work the same as the Exocet?
Ie taking out and putting in to the Boro
And building the coil and wicking?

Or are there any important differences that one needs to know ?
you can wick it the same as the exocet. works like a bomb. just line the coil up with the curvature of the top cap
 
Just a quick question @Rob Fisher or any other Flow users

Does it work the same as the Exocet?
Ie taking out and putting in to the Boro
And building the coil and wicking?

Or are there any important differences that one needs to know ?

Very similar to the Exocet Hi Ho @Silver apart from the fact that you can use a 3mm coil if you want and it has a postless deck. Also install the chimney in the boro first. And remove the airflow control and put it in the box... not needed.
 
Go to say the flavor is great on this little thing though the airflow is much less then the doggy.D1BE5982-464E-4DC4-BD9D-136BA020E4DE.jpeg63C1EBF9-5BD8-459B-90BC-78E22B40F043.jpeg E6E4E9AF-3809-457B-BB00-A3B6335C75C6.jpeg
 
I did 5 wrap kantal spaced 3mm OMG, the flavour is awsome, sorry but sxk excocet is k@k in comparison to this I am lying in the fetus poistion sucking on my Dummy here :rofl:
 
From the pic, looks like you moved the coil closer to the airflow? No need for that, coz of the slanted piece in the cap,keep the coil in the centre and the airflow should improve as well


Will give this a try next build.
 
Uncle @Rob Fisher I have an issue with my Flow, I tried to build on it as my BB arrives tomorrow, right out the box the screw in the positive post was stripped and refuses to budge no matter what I try, I've tried using a larger allen key, tapping the screw, heating and cooling, super glue, nothing's working and the screw looks horrible now, the positive post took some damage from holding it with a plier, I removed the post before I started trying to get the screw out so the rest of the Flow is fine. Any suggestions on how to get the screw out or is it possible to get just another post?
 
Uncle @Rob Fisher I have an issue with my Flow, I tried to build on it as my BB arrives tomorrow, right out the box the screw in the positive post was stripped and refuses to budge no matter what I try, I've tried using a larger allen key, tapping the screw, heating and cooling, super glue, nothing's working and the screw looks horrible now, the positive post took some damage from holding it with a plier, I removed the post before I started trying to get the screw out so the rest of the Flow is fine. Any suggestions on how to get the screw out or is it possible to get just another post?

Sorry to hear that @Moey_Ismail
I better check my Flow out too because i havent built on it yet
FYI - Skipper Rob Fisher is cruising the Med at the moment, so am not sure his replies will be as usual.
I think he is back end of next week
 
Uncle @Rob Fisher I have an issue with my Flow, I tried to build on it as my BB arrives tomorrow, right out the box the screw in the positive post was stripped and refuses to budge no matter what I try, I've tried using a larger allen key, tapping the screw, heating and cooling, super glue, nothing's working and the screw looks horrible now, the positive post took some damage from holding it with a plier, I removed the post before I started trying to get the screw out so the rest of the Flow is fine. Any suggestions on how to get the screw out or is it possible to get just another post?
Brother, have u tried using an elastic band? Place the elastic bank over the screw then Allen key on top push down just enough to secure the elastic between the key and screw and start turning slowly but keep a tight hold
 
Uncle @Rob Fisher I have an issue with my Flow, I tried to build on it as my BB arrives tomorrow, right out the box the screw in the positive post was stripped and refuses to budge no matter what I try, I've tried using a larger allen key, tapping the screw, heating and cooling, super glue, nothing's working and the screw looks horrible now, the positive post took some damage from holding it with a plier, I removed the post before I started trying to get the screw out so the rest of the Flow is fine. Any suggestions on how to get the screw out or is it possible to get just another post?

sorry man...you will have to try and drill it with a 0.9mm bit and then use a torx to get shell out. hopefully the threads are still fine and the spare screw works...Goodluck!
 
Brother, have u tried using an elastic band? Place the elastic bank over the screw then Allen key on top push down just enough to secure the elastic between the key and screw and start turning slowly but keep a tight hold
Tried that bro, the allen key size is so tiny it just punches a hole through the elastic band
 
Sorry to hear that @Moey_Ismail
I better check my Flow out too because i havent built on it yet
FYI - Skipper Rob Fisher is cruising the Med at the moment, so am not sure his replies will be as usual.
I think he is back end of next week
Those screws are really tiny, best check and not get any surprises like I did
 
Uncle @Rob Fisher I have an issue with my Flow, I tried to build on it as my BB arrives tomorrow, right out the box the screw in the positive post was stripped and refuses to budge no matter what I try, I've tried using a larger allen key, tapping the screw, heating and cooling, super glue, nothing's working and the screw looks horrible now, the positive post took some damage from holding it with a plier, I removed the post before I started trying to get the screw out so the rest of the Flow is fine. Any suggestions on how to get the screw out or is it possible to get just another post?

I have sent a message to Odis. Will let you know.


Sent from my iPhone using Tapatalk
 
sorry man...you will have to try and drill it with a 0.9mm bit and then use a torx to get shell out. hopefully the threads are still fine and the spare screw works...Goodluck!
I wouldn't attempt that myself, I'd end up damaging the threads. But maybe someone with a drill press could do it for me
 
Great new guys, I posted my issue on the Odis Designs Facebook page and a gentleman by the name of Arthur Yoon dm'd me for pics of the faulty part, asked for my shipping address and assured me that a replacement positive post will be sent to me asap with some extra screws. I've never really received bad service with any of my vape purchases but this has to be exquisite service really. Big ups to Odis Designs, will continue to purchase their products for their excellent service
 
Back
Top