I'm planning on ordering mine from Digikey.
http://www.digikey.com/product-detail/en/BH-18650-W/BH-18650-W-ND/3029217
http://www.digikey.com/product-detail/en/BH-18650-W/BH-18650-W-ND/3029217
Sx350 - 510 Connectors, Ohm Readings And Other Stuff Needed?
- Thread starter Chef Guest
- Start date
I'm leaning towards @crack2483 and going with slowtech. Free shipping FTW. Plus there are some few other things sitting in my basket at the mo. Actually just waiting for them to come with a DNA 30 clone that takes 18650 batteries.
I just don't know the quality though. Will see when mine eventually gets delivered.
Sent from my SM-N9005 using Tapatalk
what about using a slightly bigger enclose for a 26650 battery?
Should be fine though. Pretty standard stuff really (from a laymans POV). Just solder some lower gauge wire onto the contacts and happy dayz
Didn't see one on slowtech when I looked just now. But one could always get the 2 slot and run 18650s in parallel...
But $40.00 shipping? I'm could get a 3d rda clone and an Army hollow style mech mod from ST...
Why don't you guys do group buy?
I guess we could. But most of the other stuff we can get locally if we had to look hard enough. Communica has pretty much everything else needed for the build except the cursed battery holders!!!
Welcome to the world of product developers, I would highly recommend you to rather pay $$ for quality that will last, than cheapscate that will just frustrate you and place one huge damp on your enthusiasm, but that's just my opinion.
I hear you, but just to play devil's advocate, don't you think it's all made in China anyway?
Sent from my SM-G900F using Tapatalk
No its manufactured in the USA by Keystone: http://www.keyelco.com/category.cfm/Battery-Coin-Cell-Holders-Contacts-Clips/18650-Holders/id/413
PS. I'm not playing at all, just want to give you kind assistance from someone who has been doing product development for more than 20 years and don't want to see you ending up frustrated with your project.
No no! I'm being the devil's advocate. And if you know that it's a better product I believe you and will take your advice.
But then my question is what else could we get from those peeps in the USA that would be relevant to this build?
Sent from my SM-G900F using Tapatalk
But then my question is what else could we get from those peeps in the USA that would be relevant to this build?
Sent from my SM-G900F using Tapatalk
Nothing I can think of, the rest like quality switch for firing button you can get locally from RS Components: http://za.rs-online.com part no's: 690-3258 or 102-383
Johan, this chip has voltage step down, and from the spec sheet it should be able to fire a .2 Ohm coil (The figures are something like 2.5V @ 12.5Amps (Output Limit) with .2 Ohms which will give you 35W)
So yes, it will fire it, but you wont get the same 80Watts that a .2 Ohm coil would give you in a mech mod.
Does it make sense to go so low on a regulated mod... Don't think so, but it will effectively mean you can take any atty, and get 35Watts out of it
You are right, going lower than 0.5 Ohm will have zero benefit on the SX350 IMO.
Yeah, I see on that ClouporDna30 ad in the Cape Vaping Supplies forum they say "Firing 30 Watts at 0.3 ohms". Seems a bit misleading to me.
Do you guys think that there's any truth to the rumour that the firmware will be upgraded to handle 50W?
I highly doubt it, the buck converter components won't be able to handle that kind of power
Don't know - think they there could be truth to it - theoretically it should be possible
Similar threads
