SXK BILLET BOX - Reviews & Discussions
- Thread starter Deckie
- Start date
-
- Tags
- discussions reviews
My 2c as a BRRT Box owner :
1. Like good clouds bro ... although I'd give up clouds any day for flavor .... and flavor is up there with my RDAs on the Exo
2. Not even close , flavor much better on the BB and with the right build the ramp up is instant (Nii80 28g 6 wraps 2mm ID).
You can get about 4.5ml in the Borro Tank , but you won't be able to vape it all the way down due to the positioning of the coil so realistically speaking probably max 3.5ml vape-able
3. With the Exo even a total Neanderthal like me can wick it , and with pre-made coils even easier just chuck it in and chuck clouds bro!
So i got my billet yesterday, and i bought it with the set of prebuilt kanger type coils...
Its a lot tighter vape on the draw than what i have gotten used to, even with the build deck they include.
Not a bad vape, i must now get back to vaping pen style, or rather like i used to on my kangers from way back (11 months ago) rotflmao.
looking forward to seeing if this will be a adv in my rotation or not.
the jury is still out.
Its a lot tighter vape on the draw than what i have gotten used to, even with the build deck they include.
Not a bad vape, i must now get back to vaping pen style, or rather like i used to on my kangers from way back (11 months ago) rotflmao.
looking forward to seeing if this will be a adv in my rotation or not.
the jury is still out.
Can i call dibs if it does not make the cut?
Sure, you got dibs.
comes with the coil art coil kit though...
we can talk
That build deck likes being drilled to open it a bit more. 4mm. Also use flat wire?
Sent from my SM-A700FD using Tapatalk
Press the lower button and down button together.
3 taps on power button get you to mode selection.
Still trying to figure out how to lock the ohms.....beware the condensation
Can you drill out an Exocet for more airflow?
How is the airflow guys? Only thing holding me back from pulling the trigger. Is it similar to the serpent mini 22 or a tighter draw? Thanks
Someone mentioned its the holes on the side of the BB thats restricting the exocet airflow
Could be very wrong
These devices are for restricted lung hits or MTL.
I think the SM has more airflow but someone with a SM can comment.
The Exo can fit on a regular mod (it has a 510 pin)
Build a 24/26 7 wrap on a 2.5mm Id and spread the wraps slightly (not too far spaced)
Dry burn on low power and pulse to get it glowing
Pull the coil slightly down (from the post screws to the air hole it should be about 3/4 height)
Wick it tight and put the cap onto it. Cut with about 1-2mm at the side of the cap and fluff up the ends that stick out.
Juice it all up and insert into boro
I could try vaping it without the cover. That should be maximum airflow the exocet can take. Will try tomorrow.
There is an airflow ring/nut at the base of the 510 that you can adjust
The boro is fed air into 3 slits on the side of the box but you can't adjust those.
Last edited:
Yes. Was tempted to drill some holes on the cover. Try vaping without the cover to see the difference. Overtime I got used to it. Half of it is was I was too used to open flow devices. Now like it the way it is.
Completely removed the plastic bit
5 wrap 24g ni80 on 2.5id....
.35ohm vaping @20w
So would you guys say a Billet Box clone is worth getting compared to an SM22? Trying to decide if it's a worthwhile buy...
It's an awesome, versatile and compact little device. The insider offers a bit more airflow than the Exocet. You can also use stock kanger or aspire mtl coils
Sent from my iPhone using Tapatalk
Similar threads
