The just mechs thread

Dela Rey Steyn said:
I hit a 60-80w fairly regularly on the Ta-vader/DJV combo, but that's where I draw the line, after that it's just heat and vapour, not a lot of flavour, unless you count the scalding juice droplets cooling down in your throat....
Click to expand...
I basically use mostly AIOs, single coil RDL and MTL, so I usually vape 16w and at most 38w, for me it's plenty satisfying! I used the pnp coils and the new DR R mesh tank at high wattage but I always go back for the flavour I get on my other devices at lower wattage and still get plenty of heat.

Definitely each to there own, you want to suck on a blister spitting setup no worries, just post pics of the carnage, I wana see that shit!
 
To all you current mech users out there.

When I started vaping one of the major issues with regulated mods was the long firing delay. Some had a delay of almost a second in temp control. For this reason, many of us used mech mods because of their almost instant firing capabilities. I used mech mods for a few years but have completely stopped using them. Please convince me to start using them again, or even get a new shiny one. I am looking for any good excuse for me to justify the move.

The slow firing of regulated mods ended a few years ago. To be certain I checked out the cheapest new mod reviewed by DJLsb Vapes, who is probably the most tech-savvy reviewer. The response (firing) time was 12ms. To put this in context, the speed of a human eye blink is 100 to 400 milliseconds. In other words, even cheap regulated mods fire more than 30 times faster than the slowest blink.

We also used to say that mech mods hit harder. This may have been true in the distant vaping past but one can set regulated mods to wattage/voltage that would melt my ears off.

The two reasons I have raised are the main reasons I stopped using mech mods apart from safety concerns.

Please show me that I was wrong. I have no problem with eating crow as I have been married for over 30 years.
 
Mechs are like this

upload_2021-11-15_13-23-33.jpeg

You are not wrong, but there is a certain pleasure in doing the build from scratch and getting the desired result. I recommend it for any one who vapes and fears the slide into dementia. Nothing works better than having the fear of your face blown off. Millennials must stay clear because you can only blame yourself and you are not capable of that. Non binary's must stay clear as there is only one Ohms law. if you have been married for 30 years or more, or even less, don't let your wife build your mech, the reason is obvious.

Finally when her indoors shouts "get the polishing done", you can calmly without lying say " I am dear"
 
Being a tiny bit serious, mech tubes are one thing and squonks another. Take the Furyan as an example. 21700 battery, 9 ml juice bottle, a Tauren solo and squonk pin and all you have to do is make sure your build is within battery limits. 0.4/5 will still give you an awesome vape, no need to go crazy on the build. Plenty of exotic coils out there to choose from. No reason for this not to be your all day vape mod.
 
Dela Rey Steyn said:
I can't see the enjoyment of vaping 200w+
View attachment 244000
Click to expand...
Yea ull never get 4.2 off the battery. Volt drop sag etc. Vaping that low isn't pleasant in any way. Way to hot almost to the point where the juice has a completely different flavor. 2 to 3 second hits twice and feel the battery on your lips. ( usually how i check the heat) but yea, was fun. I calculate on 3.7/8 not 4.2
 
Personally for me when i use a mech i run it about .10 - .16 ohm depending the wire mass currently in my fatality i have a 0.09 ohm build and loving it plenty :headbang:
 
Resistance said:
Looking for 60A. Bliksem!
Click to expand...

There is of course a way to achieve this :rolleyes: ... you could bleed charge a couple of really large capacitors in your pockets, (you'd have to have fairly lengthy delays between puffs whilst the caps charged up too), and run some welding cables from your pockets up to your mod ... It won't be a pretty setup, but it'll give you infinity in more ways than one :giggle:
 
Intuthu Kagesi said:
There is of course a way to achieve this :rolleyes: ... you could bleed charge a couple of really large capacitors in your pockets, (you'd have to have fairly lengthy delays between puffs whilst the caps charged up too), and run some welding cables from your pockets up to your mod ... It won't be a pretty setup, but it'll give you infinity in more ways than one :giggle:
Click to expand...
That's a good current to tack some sheet metal with an arc welder.
 
Resistance said:
That's a good current to tack some sheet metal with an arc welder.
Click to expand...

Never mind tacking ... you can full on weld at that current :eek: ... Check this out;
304/316 Stainless Steel Welding Rods
  • 1.0mm = 10-25amps
  • 1.5mm = 20-35amps
  • 2.0mm = 30-50amps
  • 2.5mm = 40-70amps
  • 3.2mm = 60-90amps
  • 4.0mm = 90-120amps
  • 5.0mm = 120-170amps
 
Polishing that fire bar is a pain so rather keeping it looking aged hey at least the tip is polished IMG_20211120_165641.jpg
 
You must log in or register to reply here.

Similar threads

Stranger
The quick and easy build thread
Replies
2
Views
696
DarthBranMuffin
DarthBranMuffin
Old_Goat
Initial Impressions of the XTAR VX4 Charger
Replies
3
Views
343
Old_Goat
Old_Goat
Rob Fisher
Golisi 21700 5,000mAh Batteries
Replies
2
Views
518
Stranger
Stranger
Old_Goat
RipSaw RDA by Bearded Viking Customs and Suicide Mods
Replies
0
Views
452
Old_Goat
Old_Goat
SessionDrummer
Sterling Cloud Flavors Reviewed by SessionDrummer
Replies
0
Views
162
SessionDrummer
SessionDrummer
Back
Top