Great, have been eyeing that one for some time.
DittoThanks Paulie!
That marquis is damn impressive! Can't wait to get my own
The Nuppin Thread
- Thread starter Rob Fisher
- Start date
Will do @Alex
Thanks @Silver
I won't lie. A bit of a PITA to coil compared to the Odin. But it's certainly no cyclone nightmare.
To be honest, I did not rotate the center post at all. I gave it some thought before I installed and felt as though it wasn't necessary.
In regard to the positioning of the coil in relation to the air slots, I assume you are referring specifically to height?
I measured out the negative post leg to 8mm as the others have mentioned. After i had both coils in, I put the outer sleeve onto the atty and then lifted/lowered the coil based on what I observed when putting the sleeve on.
With regard to horizontal positioning I figured I needed to keep the positive leads straight in order for the top cap to show the width of the coil when wide open.
I hope the above makes sense? It feels like It makes sense in my head. Lol
In regard to how it's vaping, I would say extremely well!
The build I have chosen is the exact one I have in my Choc Mint Odin so I could do a direct comparison in their performance.
The flavour is outstanding on the Nuppin. I wouldn't think it possible but the flavour is even more pronounced/full bodied than the superb flavour of the Odin.
BUT
For a reason unknown to me, the Nuppin doesn't kick nearly as much in terms of how intense the vape feels. So the result (as seen with your nuppin) is a smoother, subdued experience. Not perhaps ideal when you need a real kick! And for that reason I will always keep space for the Odin in my lineup.
Thanks
Thank you kindly @Yiannaki for the detailed feedback
Very descriptive and I understand exactly what you say!
Glad you are enjoying the Nuppin and also glad you observed that "smoothness" i referred to. So its not just my imagination
On the throat hit, i suspect it has to do with the coil height as @Alex says. My coil is a "smidge" lower than the air hole. I think we need to move it a little bit higher and see what happens
Also, for me, I am enjoying it in "lung hit mode" with the air slot wide open. In that mode, I actually dont want that stonking RM2 type throat hit. Its better to have it smoother. So even if raising the coil slightly doesnt improve my throat hit, i dont mind. Then the nuppin will probably become a permanent lung hit device for me. And for that, smooth is good.
Thanks again and lets compare notes soon
Second flavour master Nuppin rocked up. Immediately tried dual coils. Slanted, 28 g, 8 wraps, 1.5 mm ID, 10 mm legs into the holes. Wicked with 2 mm Ceramic. Rocking Bowden's Mate - awesome in all aspects.
Super coiling and great pics @AndreSecond flavour master Nuppin rocked up. Immediately tried dual coils. Slanted, 28 g, 8 wraps, 1.5 mm ID, 10 mm legs into the holes. Wicked with 2 mm Ceramic. Rocking Bowden's Mate - awesome in all aspects.
I like the slanted coils. Odin style.
How are you finding the dual compared to the single 0.7 you are running in the other?
Not much a a difference actually. More throat hit, a warmer vape and a whistle.
Great coiling @Andre, I've been using a single parra coil @0.5 for the last week. And I do prefer it for my style of vape on the mini.
Main advantages for me are that the juice lasts much longer. No big difference from the duals, other than slightly less vapor... Which is fine with me.
Message sent via tapatalk
Main advantages for me are that the juice lasts much longer. No big difference from the duals, other than slightly less vapor... Which is fine with me.
Message sent via tapatalk
Hi @Alex could you post a pick of your parra coil. Really interested to see how you set it up
Yip, my single coil Nuppin is on the Mini and the dual one on a Grand. Imo the Nuppin is the ideal atomizer for the Mini - the perfect fit.
I've been running her on .45 .5 builds almost since I got her about 6mths ago. No worries here.
Thanks bud that's a great help
The luigat approach:
Haha, had a pack of 1.2Ohm eGrip RBA coils taunting me, so finally caved in, yanked out my trusty single coil, and did a dual coil build. The legs are long enough for a Nuppin and quite easy to fit. Used a 2mm drill-bit for positioning. After fitting and dry-fire tweaking the build came in at 0.7Ohm...mildy warm and fuzzy. Wicked with Jap cotton. Don't have pics, but these coils are VERY consistently built, giving near-identical glow patterns on dry fire.
Haha, had a pack of 1.2Ohm eGrip RBA coils taunting me, so finally caved in, yanked out my trusty single coil, and did a dual coil build. The legs are long enough for a Nuppin and quite easy to fit. Used a 2mm drill-bit for positioning. After fitting and dry-fire tweaking the build came in at 0.7Ohm...mildy warm and fuzzy. Wicked with Jap cotton. Don't have pics, but these coils are VERY consistently built, giving near-identical glow patterns on dry fire.
I'd call that the clever approach.
Some awesome coiling Sir. One day I'll venture into other attys.Second flavour master Nuppin rocked up. Immediately tried dual coils. Slanted, 28 g, 8 wraps, 1.5 mm ID, 10 mm legs into the holes. Wicked with 2 mm Ceramic. Rocking Bowden's Mate - awesome in all aspects.
Just be careful with the coil height, i made a quick set of new duals with a leg length of 8mm from the coil base.
They are going straight down into the negative post hole, and then angled down. Similar to @Andre build.
I thought to measure the height clearance with the top cap first, And there ain't much, perhaps 1mm. So this is just a PSA.
Message sent via tapatalk
They are going straight down into the negative post hole, and then angled down. Similar to @Andre build.
I thought to measure the height clearance with the top cap first, And there ain't much, perhaps 1mm. So this is just a PSA.
Message sent via tapatalk
Agree, make sure you test the resistance with the top cap on.Just be careful with the coil height, i made a quick set of new duals with a leg length of 8mm from the coil base.
They are going straight down into the negative post hole, and then angled down. Similar to @Andre build.
I thought to measure the height clearance with the top cap first, And there ain't much, perhaps 1mm. So this is just a PSA.
Message sent via tapatalk
This morning when I got to the vape den, I saw this:
My heart sank. My beloved REO Blue with the Nuppin had a problem.
I wiped it off and checked what seal I had used under the atty. I had used the smallest one.
I immediately changed it for the big fat one for the juice bottle cap.
I also screwed the nuppin on a bit tighter this time.
So far, I am very pleased that there are no signs of leaking throughout today. I am just hoping it makes I through the night without a leak.
If it leaks it may mean there is something wrong with REO Blue. It had a history of slight problems with the Odin but the Nuppin is working fine.
Let's see what tomorrow will bring. If it leaks I may just be tempted to send REO blue to porcupine headquarters
My heart sank. My beloved REO Blue with the Nuppin had a problem.
I wiped it off and checked what seal I had used under the atty. I had used the smallest one.
I immediately changed it for the big fat one for the juice bottle cap.
I also screwed the nuppin on a bit tighter this time.
So far, I am very pleased that there are no signs of leaking throughout today. I am just hoping it makes I through the night without a leak.
If it leaks it may mean there is something wrong with REO Blue. It had a history of slight problems with the Odin but the Nuppin is working fine.
Let's see what tomorrow will bring. If it leaks I may just be tempted to send REO blue to porcupine headquarters
Let's see what tomorrow will bring. If it leaks I may just be tempted to send REO blue to porcupine headquarters
Holding thumbs for you Hi Ho @Silver! I hope the new O-Ring sorted the issue!
This morning when I got to the vape den, I saw this:
View attachment 19829
My heart sank. My beloved REO Blue with the Nuppin had a problem.
I wiped it off and checked what seal I had used under the atty. I had used the smallest one.
I immediately changed it for the big fat one for the juice bottle cap.
I also screwed the nuppin on a bit tighter this time.
So far, I am very pleased that there are no signs of leaking throughout today. I am just hoping it makes I through the night without a leak.
If it leaks it may mean there is something wrong with REO Blue. It had a history of slight problems with the Odin but the Nuppin is working fine.
Let's see what tomorrow will bring. If it leaks I may just be tempted to send REO blue to porcupine headquarters
That sucks, It does indeed require a new 510.
NOOOO, @Alex, you cant say that - lol
Am hoping it can hold out with the fat tyre
Have vaped quite a bit on it today. And it seems fine. I cannot even see the slightest bit of leaking
But it needs to stand upright for the night and then i can know if its okay
And, another negative is i loaded a new juice in it after the mishap. I loaded the high VG Bombies Nanas Cream. The juice that leaked was 5P Bowdens Mate, which Is thinner, i think 50/50 if memory serves. So maybe the Bombies is not a good test after all.
We'll see. Maybe I must just never take the nuppin off and keep to Bombies in it. When the coil breaks, just make a new one without measuring. Lol.
That is horrible. Hope it is ok.This morning when I got to the vape den, I saw this:
View attachment 19829
My heart sank. My beloved REO Blue with the Nuppin had a problem.
I wiped it off and checked what seal I had used under the atty. I had used the smallest one.
I immediately changed it for the big fat one for the juice bottle cap.
I also screwed the nuppin on a bit tighter this time.
So far, I am very pleased that there are no signs of leaking throughout today. I am just hoping it makes I through the night without a leak.
If it leaks it may mean there is something wrong with REO Blue. It had a history of slight problems with the Odin but the Nuppin is working fine.
Let's see what tomorrow will bring. If it leaks I may just be tempted to send REO blue to porcupine headquarters
By the way, Bombies Nanas Cream is lovely in the Nuppin. Am lung hitting with just the single coil with the airflow wide open. The clouds are enormous. Actually they could just be more than a full inhale on the Atlantis. Ha ha.
Flavour is good too, but as I hve said before, the flavour on a lung hit is very different. Im not decided whether its better or worse, but its different. Less concentrated but then made up by more vapour. I am now probably a 50/50 mouth to lung versus lung hitting vaper. Lol, @Alex, your spells are working...
Flavour is good too, but as I hve said before, the flavour on a lung hit is very different. Im not decided whether its better or worse, but its different. Less concentrated but then made up by more vapour. I am now probably a 50/50 mouth to lung versus lung hitting vaper. Lol, @Alex, your spells are working...
Similar threads
