Please reserve one when u ready for me also tnks 
VapeClub - Derringer RDA
- Thread starter JakesSA
- Start date
Unfortunately I don't have many of these left, I messed up quite a few to try and get the modification done.
So say one for @Alex, @Rob Fisher ,@Andre ,@Philip Dunkley and @Yiannaki. Then I am out of stock. If anyone else wants, please be a little patient. I am looking at the catalogs now and looking to import the version with multiple caps. If I order tomorrow it should be here by next week this time.
So say one for @Alex, @Rob Fisher ,@Andre ,@Philip Dunkley and @Yiannaki. Then I am out of stock. If anyone else wants, please be a little patient. I am looking at the catalogs now and looking to import the version with multiple caps. If I order tomorrow it should be here by next week this time.
I don't mind holding out for the multiple cap version if someone else wants to take one now @JakesSA
Edit: I would actually prefer the multiple cap one to be honest
I have one with multiple caps - Ivogo clone.. @andro modded to bf for me. Have not used it yet, but am not much impressed with the quality and finish. Brass center post with brass screw at the bottom.
Is it possible to buy the centre post? Or I can just bring the one I bought and pay for it to be converted?
If you it is one of my mine I'll do the modification for free. If its not one of mine, I do charge a small fee for modification.
I would actually like one of yours.
I love the quality of your work done.
I will be happy to pay for it. It only seems fair. Don't want you to be out of pocket for no reason. Even if it's a small amount.
Apologies still half asleep here, I meant to say if you bought the Derringer from me the modification is free
That is not the version with the screw on the bottom. Is fake . U can just tap out the center post and is solid . I have two and one of them with the adjustable screw on the bottom and look similar but the top post is thinner .
Ah, thanks @andro - so it just looks like a screw at the bottom, but is not.
I collected the derringer from @JakesSA this morning, and proceeded to give it the ritual hypodermic syringe needle and sunlight soap clean out. The next order of business was to make a dual coil which came out to first .30 amd then .28 ohms. After checking the screws etc, I noticed that the center post had rotated slightly.
I used my pointed nose pliers to grip the center post, and tightened the 510 screw as much as possible, without needing to remove the coils. Checked it again on the meter, and the reading was a definite 0.28ohms.
Fired her up on the Reo with no problems at all, paying particular attention to the center post for any movement, of which there was none. For reference, I always use the 1mm o-ring on the Reo, mainly as a makeshift spring washer. After about 10 minutes I decided to try another build to test everything again.
This time around there was no problem with the center post moving, and the coil came to the expected .5 ohms on the meter. Moving it the Reo, I was particularly looking for any movement when tightening it down as far as it would go with the 1mm o-ring in place. It remained rock solid.
I'll post again later on today with any problems, should they arise.
I used my pointed nose pliers to grip the center post, and tightened the 510 screw as much as possible, without needing to remove the coils. Checked it again on the meter, and the reading was a definite 0.28ohms.
Fired her up on the Reo with no problems at all, paying particular attention to the center post for any movement, of which there was none. For reference, I always use the 1mm o-ring on the Reo, mainly as a makeshift spring washer. After about 10 minutes I decided to try another build to test everything again.
This time around there was no problem with the center post moving, and the coil came to the expected .5 ohms on the meter. Moving it the Reo, I was particularly looking for any movement when tightening it down as far as it would go with the 1mm o-ring in place. It remained rock solid.
I'll post again later on today with any problems, should they arise.
If there's any of these available please let me know. I need one.
@JakesSA will the one with the multiple caps be like the one @Andre mentioned he has (copper center post)? If so, i'll just stick to the normal one you currently have.
If it will be different a different one with SS post, then i don't mind if @TylerD takes the current one you had for me
Hi
If this modification works out please pm and I will make a list
If this modification works out please pm and I will make a list
Similar threads
