Aromamizer RDTA by Steam Crave

As requested by @Nimatek, @Wyvern and @Christos, my initial impressions on the Aromamizer.

I got the 6 ml one arguing that with my vaping style I would probably have a dedicated juice in there, saving me on filling up.

What attracted me to this tank besides the info in this thread, was the possibility of vertical coils where I could use my 4 mm Ceramic wick. And my instinct was that leaking would be less of a plague with the air paths configuration. I did not like the air flow band.

So got mine from @Vapers Corner a few days ago.

What struck me from the beginning is that this is an easy and simple tank. Take off the bottom part. Coil, wick/wet, fill, screw back in and off you go. For washing the top part is easy to take off. No violence required. No fiddling with difficult to understand juice controls. Even the air flow band, I must admit, is very easy to use and, seeing all the protective vape bands around, really does not look out of place. And, as @Nimatek said above, it does not move around at all. And if you like lots of air flow, take it off completely - as @capetocuba intimated above.

For the 4 mm Ceramic wick I needed 3.5 mm ID coils. They fitted in quite easily. Found the deck easy to work on. Used Kanthal 27 g. Think about 6 wraps per coil to end up at 0.55 ohms (0.58 on the Cuboid).

LRkVdwe.jpg


rvA8vde.jpg


Think next time (in about 3 months time with the Ceramic wick) shall use 26 g. The 27 g might be a little light weight for the tank. Probably SS.

The vape. Loaded the Aromamizer with 5p Bowden's Mate, which I vape every day via a bf dripper. Tried different wattages, up to 60 W. No dry hits. Found my preferred spot at around 45 W. Used the 2 hole air band - for my MTL, which was not a problem. Bearing in mind that the coil and wick are still settling, flavour was a bit different, but not bad different. Got a bit more mint than in my drippers. Vaporization is clearly more effective as the 12 mg hits me "hard" (inverted commas for @johan). Need to use 6 mg in the Aromamizer. So far, no leaking, not even moisture anywhere, which is a huge win for me.

This tank meets all my needs/wants. Will keep it.

Does it not look sexy on the Cuboid? Especially with the black accents (screen and air hole band):cool:

emEIK36.jpg
Thanks for that. I was concerned about the flavour being muted.
I find that there are definately big changes in flavour when the wattage goes to 60W and up as opposed to a cold but extremely flavourful vape in the reo.
So the difference for me is cold vape vs warm to hot. I find desert vapes are rather good when they are a little warm.
 
Thanks @Andre. I am happy to hear that you like the tank. I envy you the ceramic wick tho. I am struggling with loads of dry hits with the cotton bacon in the vertical build. To the extent that I want to go back to horizontal. And now my FOMO is in overdrive. I want that cuboid!

Sent from my LG-D855 using Tapatalk
 
Super write up @Andre. Thanks. Very interesting.

If it passes an @Andre Bowdens Mate test then it's good.
 
Thanks @Andre. I am happy to hear that you like the tank. I envy you the ceramic wick tho. I am struggling with loads of dry hits with the cotton bacon in the vertical build. To the extent that I want to go back to horizontal. And now my FOMO is in overdrive. I want that cuboid!

Sent from my LG-D855 using Tapatalk
Please take a pic of your build with wick. I have had dual 24g Kanthal 3.0mm ID using Japanese cotton and have never even had one dry hit.

Here's a picture of my setup.

20160115_105732.jpg
 
Last edited:


I think the difference is I use cotton bacon

Cotton bacon should not make any difference. Your coil ID looks like 2 or 2.5mm? I see you wick from under the coil then over the top of other then down. I wick individually, from top to bottom, fluff out the bottom with a thin flat screwdriver. My cotton looks like there is a lot more than yours?
 
I wicked both from top down, just cut the cotton afterwards so that there was a lot of it to pay with on both sides. That was 2,5mm and I honestly couldnt get more cotton in there, it started compressing the coils when I pulled the cotton through, and I could pick up the mod just by hanging onto the cotton. I fluffed like a madwoman and the cotton was overflowing the space at the bottom. I just need to learn to take better pictures :p That is done with SS wire since its the only one I can vape on.
 
Can I ask why please?
I have found I taste metal on all other wires. Claptons and Kanthal is second on the list to use, but I still taste a little metal on that. SS gives me the cleanest taste
 
Titanium, 26 AWG, 8 wraps @ 3.0 mm ID at 0.23 ohm. Wicked top-to-bottom with Jap Cotton, very thick wick and wick-bed on the bottom. Works wonders in TC!

My favourite -keep-pulling-out-other-builds build on the Aromamizer.
Arom_Ti_26 awg build.jpg
 
Titanium, 26 AWG, 8 wraps @ 3.0 mm ID at 0.23 ohm. Wicked top-to-bottom with Jap Cotton, very thick wick and wick-bed on the bottom. Works wonders in TC!

My favourite -keep-pulling-out-other-builds build on the Aromamizer.
View attachment 43463
Nice setup! I have been looking at my StealthVape 26g Titanium for the past 4 months ... been to lazy to try ... you got me on it! :p
 
I received my Mizer today! Build two claptons in there and vaping at 90 watts with no dry hits. Vertical coils and Swiss Roll is the way to go in this tank. Flavor is amazing and making big plums!!

2c3818bb60dd83a1012f31a2879c4e66.jpg
 
I received my Mizer today! Build two claptons in there and vaping at 90 watts with no dry hits. Vertical coils and Swiss Roll is the way to go in this tank. Flavor is amazing and making big plums!!

2c3818bb60dd83a1012f31a2879c4e66.jpg
where did you get that drip tip?:O
 
Must say I prefer the older version which can fit my own drip tip as well, making the "mouth piece and chimney longer " for cooler vape (not that this tank needs it). The extra cap is nice.
 
My favorite thing about this tank is the fact that it doesn't leak!
My favourite build so far is twisted SS single coil in the centre of the two posts.
I'm really supprised at how little cotton it needs down there.

Also having a 3ml and 6ml tank with no top nipple is well overkill for me.
I don't see the practicality in having both configurations as the 3ml top cap would be in the cuboard.
I personally like the standard drip tip and nipple.
 
Back
Top