Not the McGuyver type.....Gmf!Vape Mail Baby!
A box of Dremel goodies in a tool box! Plus some smaller chucks so I can use my baby drills and the goodies I was looking for in the first place.
View attachment 24112
Bumpedy Bump - Vape Mail!
- Thread starter Gizmo
- Start date
Quite funny how that works because it is essentially the same company. The MassMart group.OK Note to self... Do not shop at Builders Warehouse... go to Makro first! Marko is WAY cheaper! Sheeeeeeeeezzzz!
And I went back to Builder Warehouse now because they are down the road and Makro is on the otherside of the planet!
First slip of a drill on stainless steel and that whole set ends up in the gorge with blood
Now you have made me scared @johan!
But yes if there is any blood shed the Duikers Home will be peppered with Dremel and Dremel Goodies! 
Not the McGuyver type.....Gmf!
@TylerD I reiterate... I'm not a McGyver type and this could all go pear shaped very quickly... Blood could be shed and there could be wheels all over the joint... however... if I get the hole of the Hornet made better and no blood is shed and no limbs lost then I will become a McGyver specialist of note!
Now you have made me scared @johan!
Rob I assume you know that you need to punch a guide first before you start to drill and obviously you have some bullsmilk to keep the drill bit cool and lubricated whilst drilling into stainless steel?
Last edited:
Nope I didn't know about either @johan... I shouldn't need a punch to guide because there is an existing hole and I just need to make it bigger... I'm not sure if you are telling the truth about the milk or just pulling the piss?
I would say milk is less combustible than petrol ...Nope I didn't know about either @johan... I shouldn't need a punch to guide because there is an existing hole and I just need to make it bigger... I'm not sure if you are telling the truth about the milk or just pulling the piss?
Nope I didn't know about either @johan... I shouldn't need a punch to guide because there is an existing hole and I just need to make it bigger... I'm not sure if you are telling the truth about the milk or just pulling the piss?
Good if you just going to drill out the existing hole (no need for guide punch or cowsmilk). Just don't burn up the drill bit, take it slow without serious pressure on the drill bit.
PS: Bullsmilk is the real terminology used in machine shops, its a milky color fluid to keep cutting bits cool and lubricated during drilling and/or machining.
Last edited:
a bar of soap will also work as lube. just stick it in there and you good to go. smells nice to
Those bits get VERY hot when using the Dremel ... lost a bit when drilling out the Cloupor Mini door
Nope I didn't know about either @johan... I shouldn't need a punch to guide because there is an existing hole and I just need to make it bigger... I'm not sure if you are telling the truth about the milk or just pulling the piss?
Just keep in mind Uncle Rob, if you make a round hole bigger, it gets bigger in all directions, downwards too, so your risk of leaking increases. If you make it bigger with the same width, but just side to side (basically oval shaped, by gently wiggling the drill from side to side. Not too hard, or you'll break it. It works if you do it right, or you can use a cutter bit.), then you don't have that risk.
I found that out when I did my Atomic. Just keep it in mind.
Roger that thanks! It came out perfect! Video of my first dremeling currently on its way up!
Good stuff captain! Also a relief it has not killed any bambis in the gorgeRoger that thanks! It came out perfect! Video of my first dremeling currently on its way up!
Daaayyaaam!!! brother, you could tie that thing into the Eskom grid, lmao...great buy mate enjoy it.
Lovely! At the first glance it looked like 2xPanados and 2xSyndols
but I am ok know I see the Reo buttons.
Now you have made me scared @johan!
/nick gorge
In other words, if there is blood i have dibs before the Duiker
Cant wait to see your Dremel vid
/nick gorge
In other words, if there is blood i have dibs before the Duiker
Cant wait to see your Dremel vid
It went way better than I anticipated... but the video is taking forever to upload!
Similar threads
