Great tank. Easiest wicking ever for me.Thanks! I sure will!
This is a winner of a tank it seems - dual coil, airflow, capacity, size etc - couldn't find another RTA that was better on the spec sheet
Goliath V2 : Builds and Wicking
- Thread starter Yiannaki
- Start date
So i tried the vertical build on this tank, heres the specs:
24 gauge kanthal wire
around 2mm diameter
0.61 ohms.
7 wraps
So my thoughts on it:
Vapor production: it was actually good, better then the horizontal coil.
Flavor: was amazing! im still new to building but the flavor was better then most of the coils i have built
Draw: i had the airflow open full but it felt quite tight i think its because the air had to go through the tiny hole (thats what she said).
overall it was a good build, just need to get used to the draw.
24 gauge kanthal wire
around 2mm diameter
0.61 ohms.
7 wraps
So my thoughts on it:
Vapor production: it was actually good, better then the horizontal coil.
Flavor: was amazing! im still new to building but the flavor was better then most of the coils i have built
Draw: i had the airflow open full but it felt quite tight i think its because the air had to go through the tiny hole (thats what she said).
overall it was a good build, just need to get used to the draw.
Attachments
Got my Goliath v2 with my black koopor today...
Can't wait to get it started.
Can't wait to get it started.
So, two days into it i'm loving the Goliath v2.
Had some issues screwing it apart to clean it (with the cuts on fingers to match) but it performs really well.
I have only used the stock coils thus far (both Kanthal and Nickel) and so far so good.
Had some issues screwing it apart to clean it (with the cuts on fingers to match) but it performs really well.
I have only used the stock coils thus far (both Kanthal and Nickel) and so far so good.
It is even better with the RBA. Wicking is a breeze.
Received mine yesterday really like it only been using the stock 0.5 coil (unfortunately there wasnt a nickel coil with mine ) and the stock coil is giving me dry hits not wicking properly so going to try the RBA tonight.
) and the stock coil is giving me dry hits not wicking properly so going to try the RBA tonight.
Hi Matt. I bought a nickel coil separate. Mine had 2 kanthal coils.Received mine yesterday really like it only been using the stock 0.5 coil (unfortunately there wasnt a nickel coil with mine
I found that I had to prime my coil properly. I also fluffed the cotton on the wicking sides a little bit as it was packed really tight. Lastly check the juice flow control (I just leave mine wife open). I only had one real dry hit, but it was with 100vg juice. But literally gave it 10 seconds and had a drag without firing, and it was all bliss again.
Sent from within the matrix
Did the priming juice flow wide open and yesterday it was fine but today keep getting dry hits 80/20 liquid. not much fluffing possible it very tight.
Yeah, same thing happened to me the first time. Once I got that sorted, what a wonderful RTA.
Thanks,
Tried that indeed last night but still got dry hits. Did a quick build on the RBA deck and only got a occasional beginning dry hit but not allot of flavour. (40w on 26g 2,5mm 0.48 coil) But that has probably to do with my wicking havent wicked a tank in atleast 9 months
. Will adjust the wicking when i get time for now its the first tank that might be working for me.
OK so I did my first build on the rba deck last night. 28g dual came to 0.7ohm... Not what I would have wanted but hey... Had a couple of toots, and found that the nic came through much stronger on the rba build than the rocc coils. This morning I had lost an entire tank of juice. Just leaked out. Did not have this with the prebuilt coils.
Do you think I used to little wicking material? I had it just touching the juice channel, resting on the little ledge.
Sent from within the matrix
Do you think I used to little wicking material? I had it just touching the juice channel, resting on the little ledge.
Sent from within the matrix
Old school still working great. Good to be back
Similar threads
