Show Us Your Working Wick And Coil Setup

Status
Not open for further replies.
all you actually need to twist two or more together is a pair of pliers to hold onto the one end of the wires and some kind of cylindrical object with a little hook type thingy attached. some people make double twisted wire by claming the one end with pliers and looping the wire and hooking that loop onto the cap of a pen or marker then rolling the pen across their legs in one direction the whole time. cordless drill on its slowest setting, split pin and a pier of pliers is still going to give you the most uniform result though. and for the love of fudge, don't try using your dremel. :)
 
e2a3eme4.jpg


Just got the ft nem.



Lee
 
I have done a vertical coil on the rocket. Definitely need to try it on my Aqua.

Sent via Pluto on my Rocket
Yeah it is awesome on the Aqua. I just found after re-wicking, the best way for me to run the cotton to avoid any dry hits is to thread the cotton around the back of the coil then down into the channels. The criss-crossed pattern did not work to well, but looping it around the back of the coil from the initial channel and then back down to the channel that is closest, lets the wick suck up the juice constantly and avoids dry hits.

But super awesome flavor and vapor.
 
Yeah it is awesome on the Aqua. I just found after re-wicking, the best way for me to run the cotton to avoid any dry hits is to thread the cotton around the back of the coil then down into the channels. The criss-crossed pattern did not work to well, but looping it around the back of the coil from the initial channel and then back down to the channel that is closest, lets the wick suck up the juice constantly and avoids dry hits.

But super awesome flavor and vapor.
Or you coil take it right around the coil?
 
Or you coil take it right around the coil?
Yeh, just thread it around the back of the coil. So, only the back of the coil is theoretically touching the cotton. So, going from the right hand channel, around the back of coil 1, to the left hand channel, not crossed over from one channel to apposing channel.
 
Haha jip, It was just shocking to see someone saying I build a nice coil... :eek: I dont know the first thing about building coils
 
Haha jip, It was just shocking to see someone saying I build a nice coil... :eek: I dont know the first thing about building coils
It is about time, as an ecig reseller you MUST know about these things and be able to assist your customers:D.
 
It is about time, as an ecig reseller you MUST know about these things and be able to assist your customers:D.

Dear @Matthee, as much as I agree with you on this. I would need you to convince my other half, that it is crucial for me to obtain this nonage.

;) skimp skimp haha
 
That looks like a beast of a coil! Definitely giving this twisted coil concept a go tomorrow. May I ask what is your technique used to twist the Kanthal?


Sent from the TARDIS
Fix one end in a drill and other end held in a pliers by HRH and slowly run the drill till twisted as required.
One thing I found it more difficult to get the coil fixed down under the screws than with single strand coils.


Sent from my iPad using Tapatalk HD
 
Brilliant looking coil man.. Definitely got to give it a go..
 
So I was sitting around at home bored out of my mind so decided to try something new (unfortunately I do not have pics cause it was my first build, but when I try it again will take pics.

As I was saying wanted to try something new, looked around my vape draw and found an old Shooter (CE4) tank laying around doing nothing, thought to myself, I have never rebuilt a top coil, perhaps I should give it a try, after all if something goes wrong I will toss the tank as it wasnt being used.

Low and behold I managed to rebuild the coil. It is a lot like rebuilding an evod except that the cup on both ends are really long so it is hard to get clippers or scissors in there to cut the excess legs off.

Overall got it to work at 2.3ohms using cotton week, the vape is a lot hotter than that of the standard coil but I now use it as my night time zero nic device. At least this tank wont go to waste now.
 
deva9udy.jpg
udy5edu2.jpg
dyjahagu.jpg


So. Dual coil 0.9 ohms on the Origen. Fiddly to get the wick into the coil. Threading from top, then pushed it gently thru with a piece of kanthal wire.
Great vape so far with my finest juice, Gambit. Flavor is really awesome. Will test further.

Gesendet von meinem GT-I9195 mit Tapatalk
 
Status
Not open for further replies.
Back
Top