I've done it. Not recommended. Vape is a bit hot and you burn the rubber insulater very quickly. I won't be doing it again any time soon. 1.3 to 1.8 is where I like my pt coils.
Sent from my GT-I9190 using Tapatalk
Show Us Your Working Wick And Coil Setup
- Thread starter RIEFY
- Start date
- Status
Sent from my GT-I9190 using Tapatalk
Thanks man.. appreciate the info, guess I shall not be doing that.
LOLI didnt say don't try just I don't recommend it
Sent from my GT-I9190 using Tapatalk
Well from your reasons for not recommending it I dont think I should give it a try, cant stand the burnt rubber smell or taste
So Ive been busy trying something new!
Loop D Loop
26g kanthal, 9 wraps (4 on each side, and 1 extra where it began), 1.1Ohms
Vapes lika beast!!
Loop D Loop
26g kanthal, 9 wraps (4 on each side, and 1 extra where it began), 1.1Ohms
Vapes lika beast!!
And sommer cleaned everything last night so just went with a normal 9 wrap 26g coil 1.2Ohms on the Kayfun now rocking on the Nemi
Awesome stuff brother!
Looks a little unneat, but its hell getting those coils together with the wires running from side to side like that, will try again some time. Enjoying it now! Its lika duel coil on single coil ohms!
Can you give us a review of how the cotton performs?
Am considering getting a genesis style RTA and not really keen on going the s/s mesh route.
the only wick for genesis style is ss rope with a layer of cotton.
tho cotton alone works but is finicky
Sent from my GT-I9500 using Tapatalk
tho cotton alone works but is finicky
Sent from my GT-I9500 using Tapatalk
@BhavZ the cotton has to be the right size. Too much cotton and there pretty much no wicking. I have used a much thinner cotton wick and it does work. It is still slow to wick though.
@Cape vaping supplies I think that ss rope will be the best judging from what I have read on the interwebs.
Sent from my SM-N900 using Tapatalk
@Cape vaping supplies I think that ss rope will be the best judging from what I have read on the interwebs.
Sent from my SM-N900 using Tapatalk
Thanks @thekeeperza
I have used a ceramic wick on mine. Perfect and it lasts for ages. SS mesh is not that difficult either, see peeps wrap it around silica or ekowool for better wicking. Wonder how does a plain silica wick work on it - that must have been about the only choice when they came out?
- Joined
- 10/12/13
- Posts
- 123
- Awards
- 9
- Age
- 38
@Matthee , I tried a plain silica doubled over wick in the RSST, it really didn't work for me, it wasn't wicking fast enough and tilting didn't work well enough either. Cotton was better wicking, but still needed a little bit of a tilt every now and again to prevent a dry hit, ss mesh with a tiny cotton cover where the coil sits worked the best I think. I still need to try out the SS rope covered with a cover of cotten as @Cape vaping supplies suggests. But it's on the back burner, I never really had major joy with the RSST, there are other atty's which are easier to build so I kind of stopped trying! @thekeeperza your findings with cotton seem similar to mine!
Thanks...saves me the trouble of trying with silica. The ceramic wick is amazing. No tilting required. But, unfortunately, not readily available.
- Joined
- 10/12/13
- Posts
- 123
- Awards
- 9
- Age
- 38
The Kayfun version.
Here's my hand at the double barrel. Two coils in parallel consisting of 10 wraps 3og kanthal around a 1mm id (20 gauge needle). Resistance is at 0.5 ohms.
This did seem to eliminate the gurgling and leaking at first but as I'm typing this I hear that devilish *gluck gluck* and see some juice leaking out of the air hole. I turned it upside down and blew gently into the air hole with a tissue underneath the drip tip. The gurgling is gone now but I'm unsure for how long.
I've just completed this build so I'll give more feedback later but so far the vape has been very nice. Very warm with 8/10 throat hit and 9.5/10 flavour. Vapour production is a sub-par 6.5/10.
I do get an "almost" dry hit every 10 or so drags. Any ideas? Is it because the wick is too thin to accommodate the 1mm coil?
Is this how you suggest we wick the 4 channeled Kayfun @Cape vaping supplies?
Last edited:
What beautiful works of art!
yes thats the way.I think the ID is too small. try 1.5mm.
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
Nice coils there! I would suggest at least 1.5mm coils to accommodate more cotton. Also, try and make the tails even longer to fit the whole channel even in the base.
I have found that coils smaller than 1.5mm give some try hits because the cotton cant keep up the wicking for 1mm coils.
- Status
Similar threads
