I'm in! Picked this one up from @Sickboy77 earlier this week and only got a chance to fire it up now. Nice little gadget this
Glad you happy bud, enjoy the setup and juice
View attachment 112347
SXK BILLET BOX - Reviews & Discussions
- Thread starter Deckie
- Start date
-
- Tags
- discussions reviews
I have no idea what atty is in there, it's a little silver one, I suspect it's an Exocet
Whatever it is has now got a 2.4mm 24g Ni80 coil in there and it's performing quite well.Vaping some Blackout that @Sickboy77 so kindly sent with
Oh and it's already got a custom button
I have no idea what atty is in there, it's a little silver one, I suspect it's an Exocet
Vaping some Blackout that @Sickboy77 so kindly sent with
Oh and it's already got a custom button
View attachment 112354
Cool mate
Sent by iDad's iPhone
Hi @BumbleBee,I have no idea what atty is in there, it's a little silver one, I suspect it's an Exocet
Vaping some Blackout that @Sickboy77 so kindly sent with
Oh and it's already got a custom button
View attachment 112354
Where did you get the button if I may ask?
Sent from my SM-A510F using Tapatalk
If you show us a picture of the inside we can confirm what atty is in thereI have no idea what atty is in there, it's a little silver one, I suspect it's an Exocet
Vaping some Blackout that @Sickboy77 so kindly sent with
Oh and it's already got a custom button
View attachment 112354
Wow, awesome button! You say you made it? Please do tell
I did some googling, it's a ExocetIf you show us a picture of the inside we can confirm what atty is in there
Wow, awesome button! You say you made it? Please do tell
I also have an Insider that I'll play with later, as well as a whole whack of other bits that I'm sure I'll figure out over time, kinda hoping that one of those bits will allow me to use eleaf EC coils.
The button was turned on the lathe out of acrylic and then polished, quite a tricky little bugger that one, and now the wife wants one for her Gen3, an even smaller button
Exocet is definitely a good atty to start with.I did some googling, it's a Exocet
I also have an Insider that I'll play with later, as well as a whole whack of other bits that I'm sure I'll figure out over time, kinda hoping that one of those bits will allow me to use eleaf EC coils.
The button was turned on the lathe out of acrylic and then polished, quite a tricky little bugger that one, and now the wife wants one for her Gen3, an even smaller button
I also enjoy the Insider but it is a bit trickier to wick correctly. Quite rewarding once you get it right though.
That is a very good job on the button. It looks excellent. Well done man.
It makes me think of a Terminator
Good luck on the Gen3 button. Do show us the results.
My 1st Sxk BB,Thanks to @joeman187 ,coincidentally the drip tip I bought a year ago matches perfectly,will take a better pic when the sun comes out
I remember a few months ago I was bugging you and @Rob Fisher with questions and now I finally got it,still have a long way to go as im still using the standard kanger coils
And then there were two! And this one is awesome blue! (DNA40)
![IMG_0450[1].JPG](https://www.ecigssa.co.za/data/attachments/113/113673-5f03da62fa2f1304554ba924dd45bf69.jpg "IMG_0450[1].JPG")
Regards
Regards
Sitrep
Playing with the new BB which is a DNA40 model, I noted some differences.
The supplied RBA, which is basically a Sub Tank Mini RBA that came with the DNA40 is in fact version one of the RBA with the small juice hole. The only other difference between the BB RBA and the STB one is the the latter gas a shorter positive pin and therefore does not fit the BB. The standard STB RBA pin is too short and does not stick out of the tank far enough.
The good news is all parts are interchangeable so the bunch of STB RBA's I've had in storage have been put back in service.
![IMG_0452[1].JPG](https://www.ecigssa.co.za/data/attachments/113/113739-684e160025e56ed1e25e5f69b6c4f494.jpg "IMG_0452[1].JPG")
V1 cap and standard STB RBA base on the right.
The DNA40 chip also automatically detects TCR wire or not. Problem is it only knows NI200 wire so running SS or Ti causes issues. Easy enough to sort out though, just dial the temp right up and then select off. Or as I did, use a Kanthal coil.
ID 2mm, 1.2Ohm, 4V at 14W. Lovely!
Regards
Playing with the new BB which is a DNA40 model, I noted some differences.
The supplied RBA, which is basically a Sub Tank Mini RBA that came with the DNA40 is in fact version one of the RBA with the small juice hole. The only other difference between the BB RBA and the STB one is the the latter gas a shorter positive pin and therefore does not fit the BB. The standard STB RBA pin is too short and does not stick out of the tank far enough.
The good news is all parts are interchangeable so the bunch of STB RBA's I've had in storage have been put back in service.
V1 cap and standard STB RBA base on the right.
The DNA40 chip also automatically detects TCR wire or not. Problem is it only knows NI200 wire so running SS or Ti causes issues. Easy enough to sort out though, just dial the temp right up and then select off. Or as I did, use a Kanthal coil.
ID 2mm, 1.2Ohm, 4V at 14W. Lovely!
Regards
Im also in the cool kids group now. MASIVE thanks to @Rob Fisher for making it possible. Love this little thing
P.S. It was awesome to meet everyone for the 1st time in person at the vape meet. Bunch of awesome guys. Sorry i couldnt stay longer. Baby sitter was giving me a hard time
I had a sleeve of a broken V2 Kangerteck rba that i changed with the one supplied with the BB. Works lekker due to bigger juice holes
Big question now is: Insider or exocet? Suggestions please. I dont have the money to buy both. Pros and cons would be appreciated
With draw. Is it tighter than the kanger rba or more open?
Similar threads
