I guess my preference is a combination of function and appearance. I only run big dual sub ohm coils in them... and they can get hot in a small atty like the O-16. Delrin will not get hot from my long slow lung hits where the metal Syner's might with a hot enough build, and that can translate to lip skin baked on the metal DT's to clean off. Not a big deal, but one more thing to clean. So they end up being more about matchy with the mod I guess. I like slip fit DT's more than standard DT's to get the biggest wide open bore possible without the restriction of thicker DT bases and o-rings.
The Origen Little 16 BF Thread (OL16)
- Thread starter Andre
- Start date
I guess my preference is a combination of function and appearance. I only run big dual sub ohm coils in them... and they can get hot in a small atty like the O-16. Delrin will not get hot from my long slow lung hits where the metal Syner's might with a hot enough build, and that can translate to lip skin baked on the metal DT's to clean off. Not a big deal, but one more thing to clean. So they end up being more about matchy with the mod I guess. I like slip fit DT's more than standard DT's to get the biggest wide open bore possible without the restriction of thicker DT bases and o-rings.
On the search for the fruity goodness in XXX my previous 24g ni80 coil was nice but lacked something...like the sweetness. Read one of @Spydro post about big form coil and decided to build a dual 26g ka 3 id. Be very cautious on coil placement it's a little bit tight. Big step up in flavor this might be the one that stays.
Do you get any airflow with the 3mm ID?
It's good just had to make sure cotton wasn't in the way. It's obviously not as free flowing as other smaller builds.
hi guys
really dumb question...how do i access the build deck. got the top cap and afc ring off but. dnt know how to get bottom section. being smooth finish doesnt help
thx
really dumb question...how do i access the build deck. got the top cap and afc ring off but. dnt know how to get bottom section. being smooth finish doesnt help
thx
Not a dumb question, also struggled. Put the atty on a the mod/ mech and start wiggling it until its off, from there apply a little PG to the o-ring.
Edit: assemble before trying this (as @SAVapeGear mentioned below
Sent from my E5633 using Tapatalk
Last edited:
Put everything back together.Screw it onto your mod and pull by wiggling it slowly.It is tight.But it is just a pull action and wiggle action.
thx @acorn @SAVapeGear ...will try after i put baby to sleep...and she doesnt want to bloody sleep...she senses i have a new epic atty 
But have you tried the hulk smashthx @acorn @SAVapeGear ...will try after i put baby to sleep...and she doesnt want to bloody sleep...she senses i have a new epic atty
@Christos ...not at that price....i did the hulk smash on the transformer rdaBut have you tried the hulk smash
Guys. Guys. Guys!
7 wrap 26ga SS316L 2.5id with coils (ends up at around 0.2ish ohms) positioned close to the top of the posts and wicked just touching the base... Like what was suggested here. On the Therion BF mod at 45w.
Yoh.
By far the best flavour atty I have. And how can such a little thing make so much vapour with so much flavour?
I'm glad I put a proper build on this thing.
7 wrap 26ga SS316L 2.5id with coils (ends up at around 0.2ish ohms) positioned close to the top of the posts and wicked just touching the base... Like what was suggested here. On the Therion BF mod at 45w.
Yoh.
By far the best flavour atty I have. And how can such a little thing make so much vapour with so much flavour?
I'm glad I put a proper build on this thing.
Happy you found a build that is working very well for you. But realize that there are endless flavor builds that work very well in this atty when you build for the joose it will run. The why's have to do with the chamber size, the air options, how efficiently it handles fluid vortices, it's versatility, etc. Most small chamber atty's can be excellent flavor atty's, but the O-16 resides among the top shelf of all of them IMO.
My four O-16's are currently paired up with Reo P67's (small atty/fairly large mod), but my favorite place for them has always been on some of my Reo Mini 1.0's that I bought them for because to me they were simply made for these Reos.
@Spydro, I was thinking of getting beauty rings for my OL16 's on the P67? I have seen a picture on the UKS Facebook page and damn, that looks quite nice.
Picture please.
Sorry for the sizes, but there is smaller, just to gave you an idea. It rounds off the atty beautifully.
Hey guys. I'm really battling to find a decent flavour build on the OL16. Have tried dual 28g, dual 26g, single 26g (all between 0.4 - 0.6ohm bullds), raised/lowered coil/s, closer to airflow holes etc etc - but absolutely nothing closer to 'wow' running this atty on a Reo. Compared to a Cyclone AFC, it's just very underwhelming for me.
Any tips on a good flavour build, please?
Any tips on a good flavour build, please?
Lately I have been getting good flavour from single Clapton (26 kernel/32 wrap) at around 0.6 ohms (about 5 wraps).
Try building close to the posts,
coils slightly higher then the posts.
Cotton minimal and barely touching the Base.
Also try be able to see between the airhole once built and coiled. I.e see from one side through to the other.
@Andre, can you please post a picture, I also want to try some clapton's. Thanks
Here you go @Petrus. With just four wraps the ramp up time is great and you still get the good flavour of a Clapton.
If you get really desperate I'm open to swapping my cyclone with afc cap for your Ol16
So I recently build my first Clapton coil for the OL16. It is great, flavour is spot on, just the ramp up time is a bit slow. Any suggestion for builds, types of Clapton wire, diameter etc. and pictures of your builds would be appreciated.
Thanks.
Thanks.
What was your ID, wraps and resistance. What wire did you use - kernel and wraps?
Similar threads
