I think majority loves smaller chamber. I find the flavor is too intense in the smaller chambers
Sent from my GT-I9500 using Tapatalk HD
The Reomiser 2
- Thread starter devdev
- Start date
Sent from my GT-I9500 using Tapatalk HD
after today I decided to go back to my standard rm2. Had a couple of issues today where people over squonked the trident at the meet and there was juice all over. for some reason AVE gorilla juice taste BETTER on the rm2 then trident. so back to basics 13wraps 26g around blunt needle .88ohms. vapes like a boss!!!
Sent from my GT-I9500 using Tapatalk HD
Sent from my GT-I9500 using Tapatalk HD
after today I decided to go back to my standard rm2. Had a couple of issues today where people over squonked the trident at the meet and there was juice all over. for some reason AVE gorilla juice taste BETTER on the rm2 then trident. so back to basics 13wraps 26g around blunt needle .88ohms. vapes like a boss!!!
Sent from my GT-I9500 using Tapatalk HD
That is one helluva nice looking coil.
Glad we didn't have to compete against you in the coil comp bru.after today I decided to go back to my standard rm2. Had a couple of issues today where people over squonked the trident at the meet and there was juice all over. for some reason AVE gorilla juice taste BETTER on the rm2 then trident. so back to basics 13wraps 26g around blunt needle .88ohms. vapes like a boss!!!
Sent from my GT-I9500 using Tapatalk HD
Sent from my GT-I9190 using Tapatalk
thanks guys....Gaza I dont think I stand a chance against you lol. that was beautiful coils you built yesterday
Sent from my GT-I9500 using Tapatalk HD
Sent from my GT-I9500 using Tapatalk HD
Lovely rm2 coil @Cape vaping supplies
Going to try that when i get back to jhb
Was great to see you yesterday!
Going to try that when i get back to jhb
Was great to see you yesterday!
Hey Guys
So 1st of I feel honoured to be posting my coil and wick setup here for the 1st time.
Just got the Reo and straight after shining her up, I built her a new shiney coil.
28G kanthal
1.5mm ID
10 wraps
1.25 Ohm
From the side..
Heating up..
Wicked with some organic cotton.
And fire in the hole! !!
The VTF is unlike anything I have ever experienced, and I have concluded that I might need to drop to 6mg as im on a semi-silver since about 6pm.
Sent from my GT-I9500 using Tapatalk
So 1st of I feel honoured to be posting my coil and wick setup here for the 1st time.
Just got the Reo and straight after shining her up, I built her a new shiney coil.
28G kanthal
1.5mm ID
10 wraps
1.25 Ohm
From the side..
Heating up..
Wicked with some organic cotton.
And fire in the hole! !!
The VTF is unlike anything I have ever experienced, and I have concluded that I might need to drop to 6mg as im on a semi-silver since about 6pm.
Sent from my GT-I9500 using Tapatalk
.... and you had plenty DOUBTS before you pulled the trigger @PeterHarris 
??
??
Really awesome coils PeterHarris beautiful build
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
That looks awesome @PeterHarris
I usually vape 18mg , my head was spinning and I was more nauseous then a pregnant chic !
Very nice @PeterHarris, I did a quick coil after getting home earlier, I have this simple coil running at a +- 50 degree angle with the low end right over the juice hole. Very short cotton tail. Vapes good.
Quick question , the o ring seats underneath the reomizer correct ?
And there was a pic of the positioning of the air hole ?
And there was a pic of the positioning of the air hole ?
I haven't seen a need for the bottom o-ring.
The following is from this thread
Step 1: Screw the atomizer on the REO without a drip tip. Look down thru the top. See the coil? ok, You need the coil to be pointing UP when In your normal firing / hitting position ( when you bring it up to your mouth). If its not, turn it so it is. If you cant align it without excessive force (or its too loose) use the oring that came with the RBA by unscrewing the base and placing it in the drip well to achieve this. If that oring is not thick enough, I use one from a grand bottle cap. I use an oring with all RBA's to prevent over tightening to get proper alignment.
Step 2: Now look at the cap. Is the airhole DIRECTLY in front of the coil or within a few degrees of it? If not, use another oring between the cap and the base to achieve this. I had to use 2 in this location.
??
Last edited:
So where do they go ?
Yes, the o-ring sits in the catchcup underneath the RM2. Both to prevent leaking into the 510 connection and to help position the air hole correctly. Some Reonauts go without this o-ring. Some need a thicker one. Depends on how your RM2 screws on. Do not overtighten.
The cap of the RM2 is made to screw in to such a position that the air hole is situated opposite where the coil normally is. It is rarely necessary to have an o-ring there, if so, probably because the threading is damaged.
The air hole can be anywhere between 9 and 3, indicated with the blue arrowed line in the picture below. If the air hole is showing to the ground when you vape you will experience gurgling as the airflow is impeded.
Great coiling. Yip, it is a little beast.Hey Guys
So 1st of I feel honoured to be posting my coil and wick setup here for the 1st time.
Just got the Reo and straight after shining her up, I built her a new shiney coil.
28G kanthal
1.5mm ID
10 wraps
1.25 Ohm
From the side..
Heating up..
Wicked with some organic cotton.
And fire in the hole! !!
The VTF is unlike anything I have ever experienced, and I have concluded that I might need to drop to 6mg as im on a semi-silver since about 6pm.
Sent from my GT-I9500 using Tapatalk
jis i still cant get over how awesome this Reo is....
i have officially retired my MVP, aero, aero mega, nautilus, mPT3...all of it....
i saving for another reo....
i have officially retired my MVP, aero, aero mega, nautilus, mPT3...all of it....
i saving for another reo....
Dankie mnr
Way to go!!!!!
And that is quite understandable... I still can't work out how something so simple beats all the new technology hands down! And now you are saying to yourself "Why did I wait so long before getting a REO"?
Super coiling. What gauge wire?I just discovered a rattlesnake in my Reomizer, hell yeah.. built this little baby @ .64ohms.
Sick as tits
Thanks, it's .3mm which I believe is equal to 28awg
Similar threads
