Original Smok Beasts Kit

[Greyz]

#subscribed

 

[MorneW]

I luv my TFV4 minis with the Claptaon RBA. Favourite built at the mo is triple twisted SS 28g. Received my beast kit today, so will wick it up tonight. Does look like a pain in the arse to rebuild though. The clapton RBA is easy as pie. @CloudmanJHB When I wick i stuff it nice and firm, not scottish roll firm but enough resistance to almost move the coil wire. Then I cut it straight, about 1mm outside of the decks outer ring. Cotton barely in the juice wells. No leaking, no spitback and no dry hits. Running the triple twisted SS @50w and if I use 26/32 clapton I run at about 37W.

 

[CloudmanJHB]

I luv my TFV4 minis with the Claptaon RBA. Favourite built at the mo is triple twisted SS 28g. Received my beast kit today, so will wick it up tonight. Does look like a pain in the arse to rebuild though. The clapton RBA is easy as pie. @CloudmanJHB When I wick i stuff it nice and firm, not scottish roll firm but enough resistance to almost move the coil wire. Then I cut it straight, about 1mm outside of the decks outer ring. Cotton barely in the juice wells. No leaking, no spitback and no dry hits. Running the triple twisted SS @50w and if I use 26/32 clapton I run at about 37W.

Thanks a mil will give that a bash !

 

[Greyz]

I luv my TFV4 minis with the Claptaon RBA. Favourite built at the mo is triple twisted SS 28g. Received my beast kit today, so will wick it up tonight. Does look like a pain in the arse to rebuild though. The clapton RBA is easy as pie. @CloudmanJHB When I wick i stuff it nice and firm, not scottish roll firm but enough resistance to almost move the coil wire. Then I cut it straight, about 1mm outside of the decks outer ring. Cotton barely in the juice wells. No leaking, no spitback and no dry hits. Running the triple twisted SS @50w and if I use 26/32 clapton I run at about 37W.

Up Vote for cotton barely in the wells, I wet my cotton and massage it into place. All the cotton must sit on the deck with just a little dipped into the top. I'm using this method on the R2 and this method works best. Never had a leak or a dry hit this way.

 

[Cave Johnson]

@MorneW My wicking method is the same as yours

 

[MorneW]

thanks to @Dubz for showing me the light, lol. I don't get why such a lot of peeps hating on the tfv4. I have yet to find a tank that bests it. Only tank left to try out of the new releases is the griffin. Will give that a go EOM.

 

[MorneW]

Just wicked up the R3 - that was a pain in the ass but holy cow. 90W and flavour and clouds are plenty. Vape to hot for my liking and i dont think it's worth the trouble.

 

[CloudmanJHB]

Followed your advise on the wicking and seems great so far, thanks peeps

 

[Cave Johnson]

Just wicked up the R3 - that was a pain in the ass but holy cow. 90W and flavour and clouds are plenty. Vape to hot for my liking and i dont think it's worth the trouble.

Out of interest, what mod are you using?
Did you wick the standard coils that came in the deck?
Was it a 3 wrap each?

 

[MorneW]

Out of interest, what mod are you using?
Did you wick the standard coils that came in the deck?
Was it a 3 wrap each?

Used an RX200. Istick 100w says "atmoizer low" or some such. Used the coils that came pre-installed. It was triple space wrapped clapton.
I will see tonight if I am in the mood to rebuild it a bit better.

 

[Cave Johnson]

Used an RX200. Istick 100w says "atmoizer low" or some such. Used the coils that came pre-installed. It was triple space wrapped clapton.
I will see tonight if I am in the mood to rebuild it a bit better.

Cool thanks. Yeah mine was 0.14ohms, quite low for a non TC build.
I ask because I'm using it on the cuboid and it doesn't allow you to hit that 25A draw limit so the mod maxes out at around 87W with this particular build.