The Reomiser 2
- Thread starter devdev
- Start date
It is chrome covered brass, @andro
You can polish it up with autosol its made for chrome. But no abrasive polishing. They all come chromed and the chome is sanded off to make a brass one.
Its made out of brass and chrome plated Andro.
PS: didn't see you already received the correct answer/s.
Hi guys. So after reading most of this long thread, I just want to ask a question I'm sure has been asked many times before so bare with me please
I'm looking for the best build to do on my rm2 on my Reo mini lp. Throat hit is not a big issue for me, I'm rather looking for the most flavorful build, with moderate vapour production. Thanks in advance!
I'm looking for the best build to do on my rm2 on my Reo mini lp. Throat hit is not a big issue for me, I'm rather looking for the most flavorful build, with moderate vapour production. Thanks in advance!
Hi guys. So after reading most of this long thread, I just want to ask a question I'm sure has been asked many times before so bare with me please
Singel coil
28g 4/5 wrap 2mm id spaced ugly coil
Gives you about 0.8ohm
One battery per bottle
So when you change juice you pop in a fresh battery
Hi guys. So after reading most of this long thread, I just want to ask a question I'm sure has been asked many times before so bare with me please
Hi @Vape_r, do you like a crisp vape or a more dense, wetter vape?
Also what juices do you like vaping in the Mini? (tobaccoes, desserts, menthols, fruity menthols)
To get the most flavour from the RM2 position your coil as close to the edge and as low on the deck as possible. Of course your coil must be just behind the air hole.Hi guys. So after reading most of this long thread, I just want to ask a question I'm sure has been asked many times before so bare with me please
Can someone maybe post a picture if they have time, of how I should position my coil.
Hi there, I prefer a more denser Vape and I usually Vape dessert and fruity flavours.
Last edited:
If you start at page 1 of this thread you will get tons of pictures and ideas on how to coil the RM2. When we started an ID of 1.5 mm was sort of the standard, but nowadays it is more like 2.5 mm.
Hi @Vape_r
The RM2 is a masterful atty and your coil position plays a big role in the vape.
For more throat hit, make it a bit higher than the airhole (eg bottom of coil in line with top of airhole) and move the coil a bit closer to the center. You lose a little bit of flavour that way, but throat hit is huge.
For more flavour, as @Andre says, move the coil closer to the edge (rim) of the atty and bring the coil low down, just above the ceramic deck. The top of the coil will probably then be in line with the bottom of the airhole. This lessens throat hit but tends to increase flavour.
I often find a happy medium in the middle of the above two. Quite close to the edge of the atty with the coil fractionally above the airhole.
Its quite remarkable how moving the coil just 1mm up or down or towards the inside or edge can make quite a big difference in the flavour and throat hit. At all times your coil should be inline with the airhole. So what i do is i make a mark with a black koki pen on the base of the atty where the airhole is when the cap is screwed on. Then i know exactly where to position the coil when the cap is off and i am installing the coil.
As for the type of coil, if you want a bit of a denser vape, i would say try 27g or even 26g. Make a simple compressed microcoil of around 2mm ID and say around 0.8 ohms resistance (dont go very low on the Reo Mini because those little batteries shouldnt be pushed too hard).
I prefer the crispness of the 28g single coils or the 29g or 30g paracoils which essentially just gives you more surface area. Ie more volume of vape.
You will need to experiment with
- gauge of wire (i would say 27g or 26g for a denser vape, but that is not my speciality)
- coil ID - probably 2mm or 2.5mm
- compressed versus uncompressed - to see what you prefer
But the coil position info I shared above i think will hold true no matter what actual coil you build.
Hope it helps
Let us know how it goes. Will try find pics for you
Hi @Vape_r, the following posts might help you further and have some pics
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-41#post-162569
This one is a classic from @RIEFY
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-16#post-82974
Another good one, showing close to the edge. This may be just a little too close. You dont want the coil to touch the RM2 cap
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-4#post-36771
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-41#post-162569
This one is a classic from @RIEFY
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-16#post-82974
Another good one, showing close to the edge. This may be just a little too close. You dont want the coil to touch the RM2 cap
http://www.ecigssa.co.za/the-reomiser-2.t1596/page-4#post-36771
Very neat coiling - you have skills
. But I have now been waiting for almost 2 hours on your report back - am very curious.Damn! I have never experienced such rich flavour!! I now understand what everyone means when they rave about Reos. I haven't been on the forum because I've been too busy vaping but thanks so much for the help guys. Really thinking about selling all my mods and putting it towards maybe another Reo... Or two
but thanks so much for the help guys. Really thinking about selling all my mods and putting it towards maybe another Reo... Or two
Great stuff. Thanks for the report.Damn! I have never experienced such rich flavour!! I now understand what everyone means when they rave about Reos. I haven't been on the forum because I've been too busy vaping
Good Day. Need some advice from Reonauts. Mod:Reo Mini, Atty:Rm2. My current coil setup is 28g 316l, 8 wraps, 2 mm, 0.6ohm. Wick cotton bacon V2. All of a sudden my sweet spot is gone? Need a coil setup advice for this atty and mod. Thanks in advance.
Hi @Petrus
I haven't ventured into Stainless Steel coils yet.
my Reo Mini is sweet spotting on a simple 28g compressed Kanthal coil - 1.5mm ID - about 6 wraps - so about 0.9 to 1.0 ohms. Nothing too hectic for the little battery.
I set my coil up pretty close to the edge of the atty and fairly high up (bottom of coil about in line with the airhole) - this gives me decent flavour and good throat hit.
@Silver, I got my perfect build, also a micro coil, but accidentally burn my coil when re wicking, now I battle to find that sweet spot. The Origen l 16 on the other hand, no matter what build, the taste is always spot on.....damn, I should have ordered 2
Lol
You need a little black book where you take notes of what you did and how it vaped...
And you guys with that Origen 16 are making my FOMO meter tick up....
You need a little black book where you take notes of what you did and how it vaped...
And you guys with that Origen 16 are making my FOMO meter tick up....
Maybe try a bit higher in resistance. From around 0.75 to 0.95.
What are you missing - flavour, throat hit or clouds?
@Andre, flavour????? I am not a big cloud chaser, but I love excellent flavours. And I got it, but now it's gone. The OL16 on the other hand10/10
Coil as close to the edge as possible and as low on the deck as possible. And, as I suggested above, try a bit higher resistance.
Agree, the OL16 is the best!
Similar threads
