The Reomiser 2

Before i started reading all these comments there was no flavour drop. Now with everybody sayin it now my mind says wait a bit maybe there is. And my wallet already going ohhhhhhhhhh f@#k
Do not be too concerned. Many, many Reonauts have drilled theirs out and are very happy.
 
So the last coil I build was a 1.3ohm coil, vaped it for about 2 weeks. It was not to my liking.

So tonight I decided to build another one.

Started out as normal
26g
2mm id
4 wraps
(My normal sweet spot, around 0.8 ohms)

Then, as I was working the 1'st little leg into the one post, it was as if the coil was talking to me, guiding me to turn it on its side.

ImageUploadedByTapatalk1429811778.898427.jpgImageUploadedByTapatalk1429811792.309549.jpg

And then loadsheding stroked!!

And the generator came to the rescue

So now it was wicking time

ImageUploadedByTapatalk1429811887.168854.jpg

And juicing it up time

ImageUploadedByTapatalk1429811912.934375.jpg

And vaping time...

Um... No pick... But it vapes amazing!!!
 
Nice vertical coil @annemarievdh !
How does it compare to normal horizontal coils?
Does it wick as well?
 
after reading about the ekowool lastnight i rebuilt my RM2 with ekowool again, tried it until now, but im sorry - i cant like to be linking the tatse :(

i prefer my rayon, even tried that native wick and jap cotton - still rayon it where it is at for me - juice VM4
 
after reading about the ekowool lastnight i rebuilt my RM2 with ekowool again, tried it until now, but im sorry - i cant like to be linking the tatse :(

i prefer my rayon, even tried that native wick and jap cotton - still rayon it where it is at for me - juice VM4

No argument there @PeterHarris! I keep trying the other stuff every now and again and it's Rayon all the way for me!
 
Advice needed... My RM2 is showing some age signs...chrome is scratched and starting to crack...
Any advice on a safe way to refinish/restore it... Don't want to damage it so thought I'd ask the gurus on here first.

Txs
 
Advice needed... My RM2 is showing some age signs...chrome is scratched and starting to crack...
Any advice on a safe way to refinish/restore it... Don't want to damage it so thought I'd ask the gurus on here first.

Txs
Many take the chrome off. That is how the brass RM2 sees the light of day. Presume starting with a coarse sandpaper going finer.
 
Hi all

Just a word of caution - be careful if you try fiddle with the RM2 posts. They can break.

This is what happened to me today.

I decided to rebuild a coil in my LP RM2 (currently on Reo Blue). But when I took out my coil, this is what my posts looked like:

RM2 wonky.jpg

The post holes on the left post (near the squonk hole) were not aligned correctly. Also, that post seemed like it had tilted slightly.

I know that these posts screw in and out so I tried to screw it a bit to get the post holes facing the correct way. I put a needle through the post holes and turned it a bit anti-clockwise. The post rotated and the post hole was in the correct position - but it was loose. I then turned it the other way (clockwise) and it got a bit tighter in the position in the photo above. Then I turned a bit more...

Snap

RM2 broken.jpg

The top of the post just snapped off!
I wasn't even applying much force.

I actually asked @johan what I should do after I took the first picture. I recall him having taken the RM2 apart recently. But I was impatient and saw a thread on ECF where they showed how to disassemble the RM2. So I thought I could just tighten that post quite easily before waiting for Johan's reply....

What's the moral of the story?
  • Be very careful with the RM2 posts - they are not very strong and must be handled with care
  • Wait for an advice from an expert before fiddling yourself. (Unless you are familiar with it)
I am wondering if I can get another "squonk hole" post and resurrect this RM2 or whether this one just needs to be kept as spares...
 
PS - Johan did come back to me about 10 minutes after the "snap" and said to me that the left post looked like it could have been cross-threaded

As a matter of interest @johan, had I waited for you, do you think this could have been corrected? Or do you think that post was already toast?
 
@Silver it is difficult to judge without the unit in hand, but lets assume it was cross threaded - in that case a gentle unscrewing and correctly aligning threads, it could've saved the post.
 
Hi all

Just a word of caution - be careful if you try fiddle with the RM2 posts. They can break.

This is what happened to me today.

I decided to rebuild a coil in my LP RM2 (currently on Reo Blue). But when I took out my coil, this is what my posts looked like:

View attachment 30930

The post holes on the left post (near the squonk hole) were not aligned correctly. Also, that post seemed like it had tilted slightly.

I know that these posts screw in and out so I tried to screw it a bit to get the post holes facing the correct way. I put a needle through the post holes and turned it a bit anti-clockwise. The post rotated and the post hole was in the correct position - but it was loose. I then turned it the other way (clockwise) and it got a bit tighter in the position in the photo above. Then I turned a bit more...

Snap

View attachment 30931

The top of the post just snapped off!
I wasn't even applying much force.

I actually asked @johan what I should do after I took the first picture. I recall him having taken the RM2 apart recently. But I was impatient and saw a thread on ECF where they showed how to disassemble the RM2. So I thought I could just tighten that post quite easily before waiting for Johan's reply....

What's the moral of the story?
  • Be very careful with the RM2 posts - they are not very strong and must be handled with care
  • Wait for an advice from an expert before fiddling yourself. (Unless you are familiar with it)
I am wondering if I can get another "squonk hole" post and resurrect this RM2 or whether this one just needs to be kept as spares...
Bad luck there. Keep it as spares, unless someone has an bottom of the drawer one with an intact post.
 
@Silver sorry for your troubles. Those posts are chrome plated or nickel plated brass as far as metal goes its as hard as cheese.
 
Last edited:
aah man that had to break your heart when that thing snapped.
@Rob Fisher has a good point on the Cyclone. i would get a new RM2 and a Cyclone they are both fantastic but i seem to mostly use the Cyclone.
 
Just wanted to say that I am so touched by the generosity of members

This afternoon, after my RM2 episode, i get a PM from @kimbo to offer me his RM2 for no charge

Kimbo, you are a legend!

Whether I end up accepting the offer or not, that is a great act of kindness and you are a true gentleman for making the offer. I appreciate that so much. Just wanted to let everyone know.
 
Back
Top