Thanks Oom Rob, I even see on the ECF forums the guys are gagga about this atty, with some massive hits and excellent prices if they can find.
The Nuppin Thread
- Thread starter Rob Fisher
- Start date
Here is the Nuppin thread with many builds: http://www.ecigssa.co.za/the-nuppin-thread.t7561/
Maybe mods can merge the threads.
Maybe mods can merge the threads.
For me the Nuppin is a superb atty for lung hits on fruity menthol juices.
I have only tried dual coil builds with 26g, 28g, 29g and 30g Kanthal
For me the sweet spot is 29g Kanthal - about 5 or 6 wraps on each coil - 1.6mm ID
I love it with Rayon wick for the menthols and fruity menthols.
Flavour is good and with the thinner wire and small ID, I get a lovely crisp vape
The tricky part for me with the Nuppin is making sure to measure the length of the negative leg because that determines the height of the coil. I am around 8mm or 9mm. The other tricky bit is installing the coils because it sometimes requires a bit of patience. If I am in a bit of a hurry, I struggle.
Vape is very flavourful for me
Have yet to try a single paracoil on the Nuppin...
I have only tried dual coil builds with 26g, 28g, 29g and 30g Kanthal
For me the sweet spot is 29g Kanthal - about 5 or 6 wraps on each coil - 1.6mm ID
I love it with Rayon wick for the menthols and fruity menthols.
Flavour is good and with the thinner wire and small ID, I get a lovely crisp vape
The tricky part for me with the Nuppin is making sure to measure the length of the negative leg because that determines the height of the coil. I am around 8mm or 9mm. The other tricky bit is installing the coils because it sometimes requires a bit of patience. If I am in a bit of a hurry, I struggle.
Vape is very flavourful for me
Have yet to try a single paracoil on the Nuppin...
@Petrus, I'm getting a very flavourful vape, on par with the cyclone except it's a warmer vape and brings out some of the subtle flavours.
26 AWG
316L SS
.3 ohms
2.5mm ID
Dual coil
Just re wicked with fibre freaks #2.
Try putting the coils low and as close to the edge as possible.
I haven't managed to get a single coil to the cyclone level yet.
Only build that has really been good for me this far.
26 AWG
316L SS
.3 ohms
2.5mm ID
Dual coil
Just re wicked with fibre freaks #2.
Try putting the coils low and as close to the edge as possible.
I haven't managed to get a single coil to the cyclone level yet.
Only build that has really been good for me this far.
@Silver, I did a paracoil, and the vape is super. 28Ga ss 316 1.5mm. I want to order some 30ga kanthal, only for parracoils, I think it will work out just fine. Any suggestions would be great.
The nuppin is super easy to build on if you adjust the center post hole to a 45degree position. Instead of the 90 degree, relative to the negative hole.
For me, eveything about this atty is super.
Oh, and I use a vernier to measure exactly 8mm for the negative wire.
For me, eveything about this atty is super.
Oh, and I use a vernier to measure exactly 8mm for the negative wire.
Any suggestions on single coil builds?
The best two single coil builds so far for me is either the parracoil or the one I did with the competition wire.
Only used a single parallel coil once, try a center build over the positive post. This allows for better dual airflow on a single coil.
It does work well
When I tried single coils I put it in the same place as the duals with only one coil. This suggestion sounds very promising!
Thanks!
Just mentioning..... for single coil builds remember to close off the air hole on the side that does not have the coil, except if you are using @Alex build above.
My Nuppin rebuild and re wicks don't take that much time for me. I`ve only ever used dual spaced coils in the Nuppin and flavor and vapor production is on point. 30 gauge twisted Kanthal, 6 wraps around the little blue screwdriver and position the coils so that they are in line with the air holes and about a mm from the edge. I usually don't measure the negative leg length. I just eyeball it. One thing I`ve learnt though is to let the positive leg of the coil come from below. (see pics). I also lightly tighten the negative leg to hold the coil in place while I measure trim and insert the positive leg. Once the positive legs are secured I loosen then re tighten the negative legs. I`ve found using this method the easiest to build with. I also compress the coil more after I`ve dry burned it.
*Edit: build come out to 0.44 ohms
Last edited:
This was the result of the twisted 0.44 ohm dual spaced coils on the Nuppin. Juice: Cloud Company with a little VG added.
Could be used with a cyclone aswell
Did you perhaps order more than 1 pack @Rob Fisher ?
Awesome posts @Blu_Marlin
You have the Nuppin aced!
You have the Nuppin aced!
I didn't but I can... but with free shipping you should just order direct? Save the R60 courier fee when it arrives?
Except the negative lead goes straight down. (hence the need for the 8mm length.)
watch this one
Last edited:
@Rob Fisher I did get extra screws with the nuppin I bought. Will try them in the cyclone 
Similar threads
